Eaton Remote Power Panel User Manual Download Page 39

Page: 39 / 64

Installation

Eaton Remote Power Panel (RPP) User’s Guide 164202125—Rev 5

www.eaton.com/powerquality

Figure 15. Shunt Trip and Auxiliary Contact Terminal Detail

Initial Startup

WARNING

Only qualified service personnel (such as a licensed electrician) shall perform the initial startup. Risk of
electrical shock.

To start up the RPP:

Turn off utility power at the distribution point where the RPP will be connected. Be absolutely sure there is
no power.

Verify that all circuit breakers are in the OFF (O) position. For layout, see Figure 6 on page 12.

Remove any foreign objects from the interior of the unit.

Note:

Verify that intake and exhaust air screens are clean and free of obstruction.

Complete the installation checklist (see 27).

Turn on utility power to the RPP.

NOTE

Letter A in the terminal designation indicates the top panelboard main breaker and letter B

in the terminal designation indicates the bottompanelboard main breaker

(Rotated for Clarity)

Table 7. Shunt Trip and Auxiliary Contact Terminal Block Terminations

Terminal Function

Rating

Size of Pressure

Termination

Tightening Torque

Nm (lb in)

Type Screw

Comments

Auxiliary Contacts or Shunt Trip

600V, 20A

#26–#12

0.4 (3.5) - 0.8 (7.1)

Slotted

Use twisted-pair wires for each input and
return or common.

Strip wire insulation

back 10 millimeters to wire terminal blocks.

Summary of Contents for Remote Power Panel

































































Search results

Summary of Contents for Remote Power Panel

Reviews:

Related manuals for Remote Power Panel

Brands by name

Popular brands

Eaton Remote Power Panel, User Manual

Search results

Summary of Contents for Remote Power Panel

Reviews:

Related manuals for Remote Power Panel

Brands by name

Popular brands