manualshive.com logo in svg

Eaton Power Xpert PD Series, Manual, Page: 21 / 58

Share
Download
Eaton Power Xpert PD Series Manual Download Page 21

17

6  Power Xpert® Protection Manager - configuration software

PXR tRiP units foR PoweR Defense molDeD case ciRcuit bReakeRs

   MN012007EN   June 2018   www.eaton.com

5.4 Neutral voltage sensor

For applications with a neutral conductor external to the circuit breaker, a small module is 

provided.  This module has wire leads and must be used between the neutral conductor and 

the voltage sensor input to the trip unit.  The neutral voltage provides a reference to accu-

rately measure voltages in “Y” connected power system. 

IMPORTANT:

 This module contains circuitry to reduce the line voltage to levels accepted by 

the trip unit.  Failure to use this module for neutral sensing may cause permanent damage 

to the trip unit.

6  Power Xpert

®

 Protection Manager - configuration software

Eaton’s PXPM is a Microsoft

®

 Windows-based software that configures, controls, monitors 

and tests Eaton PXR trip units.  The user can create, modify, and save configurations for a 

PXR trip unit.  The software further allows user to reset trip units, adjust trip unit’s date and 

time, capture current or voltage waveforms, and perform trip or no-trip tests.
The software is available as a download from the following link: www.eaton.com/PXPM.
The Power Xpert Protection Manager provides two key features.  You may choose set point 

configuration to create, modify and save configurations for PXR trip units.  The remote 

control and test offers users the ability to reset trip units, adjust trip unit time, capture 

current or voltage waveforms, perform trip or no-trip tests and generate test reports.

6.1  Set point configuration through PXPM

Key to configuring your trip unit is the configuration screen, which allows users to view and 

edit set points.  

Summary of Contents for Power Xpert PD Series



























































Reviews:

No comments