background image

12

Effective January 2017

NOVA

®

 15i, NOVA 27i, and NOVA 38i; Three-phase

microprocessor-controlled; installation and operation
instructions (S280-43-1)

Instructional Literature 

IL0104001E

Operation

Electrical operation

The NOVA i recloser utilizes an interface circuit located in the 
mechanism housing. The electronic interface circuit controls the 
opening and closing signals to the magnetic actuator.

OPEN/CLOSE contact position indicator

The OPEN/CLOSE contact position indicator consists of a red 
CLOSED and a green OPEN indicator located on the bottom of the 
mechanism housing (see Figure 13).

Hotstick operation (manual open, electrical 
close)

The recloser may be opened manually by using a hotstick to pull 
down the yellow manual OPEN handle, located on the front of the 
recloser (see Figure 13). To close the recloser after a manual 
opening, first, push the yellow manual open handle up. Then, using 
the microprocessor control, close the recloser.

 

If the yellow manual OPEN handle remains in the down position, the recloser 
cannot be closed electrically from the control.

IMPORTANT

This equipment is not intended to protect human life. Follow all locally 
approved procedures and safety practices when installing or operating 
this equipment. Failure to comply can result in death, severe personal 
injury, and equipment damage.

WARNING

Hazardous voltage. Do not rely on the open position of the yellow 
operating handle or the contact position indicator; it does not ensure that 
the line has been de-energized. Always establish a visible disconnect. 
Failure to follow proper safety practices can result in contact with high 
voltage, which will cause death or severe personal injury.

WARNING

Hazardous voltage. Always use a hotstick when working with this 
equipment. Failure to do so could result in contact with high voltage, 
which will cause death or severe personal injury.

WARNING

Hazardous voltage. Never rely on the open position of the operating 
handle or the contact position indicator; it does not ensure that the line is 
de-energized. Follow all locally approved safety practices. Failure to 
comply can result in contact with high voltage, which will cause death or 
severe personal injury.

WARNING

Figure 13.

NOVA i recloser OPEN/CLOSE contact position indicator, 
nameplate, and manual OPEN handle.

OPEN/CLOSE Contact 

Position Indicator

Nameplate

Manual 

OPEN Handle

Summary of Contents for NOVA 15i

























Reviews: