background image

6

Instruction Booklet 

IB157001EN

Effective May 2015

Fixed capacitor banks (Unipump, Unipak, and Unipak 

detuned filter) low voltage (600 V and below), NEMA 1 

NEMA 3R (outdoor) enclosed versions 

EATON

 www.eaton.com

F-c

Cleared fuse light

Cleared fuse light

Cleared fuse light

A2

Incoming

1 A

F-2

1 A

F-1

270 k

Ts-1

Ts-2

Capacitor  enclosure

Overtemperature light 

Customer incoming

conductor connection

(90 °C copper

conductor cables

at 75 °C ampacity)

Customer

interconnect

Three-phase internally

delta connected capacitor 

A1

B2

B1

C2

C1

A

B

C

Reactor enclosure

F-c

F-c

Three-phase

reactor 

Customer

interconnect

terminals

provided with

Unipak detuned filter

Ground

terminal

Ground

terminal

Bonding

conductor

Connection conductors

and conduit provided

by customer. Same size

as incoming conductors.

Customer

termination

terminals

provided. 

Reactor thermal switches

(embedded in windings)

(normally closed)

Note: 6-inch minimum clearance on reactor top and sides for ventilation. 12-inch clearance 

is preferred. See equipment drawings for Unipak detuned filter wire lug sizes.

Figure 1. Connection schematic

Motor

Motor

feed

Motor

starter

Fused

safety

switch or

breaker

Install

at location:

Capacitor

C

Capacitor

B

Capacitor

A

Thermal 

overload

B

A

C

Figure 2. Capacitor connection locations

Summary of Contents for NEMA 1













Reviews: