background image

4

Instruction Leaflet 

IL 29C702E

Effective April 2015

Installation Instructions for the HKDDC 

Circuit Breaker and Molded Case Switch

EATON CORPORATION www.eaton.com

Table 2.  Terminal Types

Terminal 

Cat. No.

Terminal

Material 

Body

Screw 

Head 

Type

AWG 

Wire

Range

Metric

Wire 

Range

Wire

Type

Torque

Value

lb-in

(N.m.)

TA300K

Aluminum

Socket

3-350(1)

35-150

Cu/Al

275 (31.1)

TA350K

Aluminum

Socket

250-500(1)

150-240

Cu/Al

371 (42.4)

TA400K

Aluminum

Socket

3/0-250(2)

70-120

Cu/Al

275 (31.1)

TA401K

Aluminum

Socket

250(2) or

500(1)

120(2) or

240(1)

Cu/Al

275 & 375 

(31 & 42)

TA402K

Aluminum

Socket

500-750(2)

240-300

Cu/Al

550 (62)

T300K

Copper

Socket

3-350(1)

35-150

Cu

275 (31.1)

T350K

Copper

Socket

250-500(1)

150-240

Cu

375 (42.4)

T400K

Copper

Socket

3/0-250(2)

70-120

Cu

275 (31.1)

Figure 6. Cover Mounting Hardware.

Figure 7. Cover Screw Installation Positions.

Figure 8. Terminal Cover Installation.

Figure 9. Terminal Installation.

 WARNING

BEFORE MOUNTING THE CIRCUIT BREAKER IN AN ELECTRICAL SYSTEM, 

MAKE SURE THERE IS NO VOLTAGE PRESENT WHERE WORK IS TO BE 

PERFORMED. SPECIAL ATTENTION SHOULD BE PAID TO REVERSE FEED 

APPLICATIONS TO ENSURE NO VOLTAGE IS PRESENT. THE VOLTAGES 

IN ENERGIZED EQUIPMENT CAN CAUSE DEATH OR SEVERE PERSONAL 

INJURY.

NOTICE

DEPENDING ON THE EQUIPMENT CONFIGURATION, THE CIRCUIT BREAKER 

CAN BE MOUNTED USING DIFFERENT STYLES OF HARDWARE. THE FOL-

LOWING STEPS DESCRIBE HOW TO MOUNT THE CIRCUIT BREAKER USING 

STANDARD HARDWARE. WHEN SPECIAL HARDWARE IS NEEDED (FOR 

EXAMPLE, WITH THE ELECTRICAL OPERATOR), THE INSTRUCTION LEAFLET 

DESCRIBING THE ACCESSORY ALSO DESCRIBES THE SPECIAL MOUNTING 

ARRANGEMENTS.

1

2

1

3

2

4P

3P

1

2

Screw, No. 8x 1.88 Inch, Flat Head, Cross-Recessed,

Thread Forming.

Screw .190-32 x 3.125 Inch Pan Head, Cross-Recessed.

 Note: Hatched lines show additional pole and screw for

            4-pole circuit breaker.

2

1

2

4P

1

3P

2

1

3P

2

1 3P

4P

                                           

            3 - Pole         4 - Pole

No. 8 x 1.88 in, Flat - Head 

                 6 

           3

.190 - 32 x 3.125 in, Pan - Head                   2                  7

Pan Head Screws

Flat Head, Thread

Forming Screws

Summary of Contents for HKDDC Series









Reviews: