background image

8

EATON    

 IB528001EN

    

 Installation instructions

Installation Instructions - Arena Series

WARNING

NEVER connect the bare or green insulation ground wire to the black (HOT) current-carrying or white (NEUTRAL) 

supply wire, as this could energize the metal housing and create the risk of electrical shock. FAILURE TO FOLLOW 

THIS WARNING MAY LEAD TO DEATH, SEVERE INJURY, OR PROPERTY DAMAGE.

WARNING

Do not damage or cut the wire insulation (covering) during installation.  Do not permit wires to contact any surface 

having a sharp edge, as this may damage the wire insulation and create the risk of electrical shock. FAILURE TO 

FOLLOW THIS WARNING MAY LEAD TO DEATH, SEVERE INJURY, OR PROPERTY DAMAGE.

Control Wiring

WARNING

Always turn power to Luminaire OFF before performing any work on control wiring. Turn transmitters off before 

working on main control lines. Performing any work on control connections while Luminaires are receiving the signal 

may result in transient or fluttering control signals which can cause damage to the luminaire. FAILURE TO FOLLOW 

THIS WARNING MAY LEAD TO LUMINAIRE INTERNAL DAMAGE AND FAILURE.

Control Standards

All control work shall conform to ANSI E1.11 – 2008 (r2013), USITT DMX512-A, Asynchronous Serial Digital Data Transmission 

Standard for Controlling Lighting Equipment and Accessories. At a minimum, DMX cable shall be 1-pair (24AWG, 7x32 

Stranding) Twisted (minimum of 4.8 twists/foot), Shielded (minimum of 100 ohms impedance) and <25pF/ft. Capacitance.

WARNING

Use caution when connecting any 24AWG wires as they are more prone to breaking. 24 AWG may be used in 

terminal blocks. If wire will be connected with wire nut, wago connector, or other mechanical splices, use 22AWG 

wire.

LANDBURST CONTROLSe:

 Plug in the control lines via the 3-pin XLR whips provided with the luminaire. Use the male 

XLR as the DMX input and the female as the DMX output to reduce the risk of injury and poor connection. Use an RDM 

controller to set the DMX start channel(s) of the fixture.

Figure 6. XLR Cables

Male DMX In

Female DMX 

Out

Summary of Contents for ephesus Arena Series

















Reviews: