10
Mounting and Operating Instructions Fire-Resistant Cabinet Type DualGuard-S ESF30 October 2022 www.eaton.com
5 Transport
5 Transport
5.1 Brief notes about important transport
considerations
• Note the tipping hazard during transport!
• Only remove the protective foil, the protective corner pads,
or other packaging material directly at the setup location!
• Note the included assembly materials on the protective
foil or the enclosure!
• Never transport the equipment with doors open!
• At least 2 persons must always be available when trans-
porting equipment!
• When using a forklift for transport, use appropriately long
forks to match the overall dimensions.
• Watch for parts that protrude or stick out.
• Never step under suspended loads when using a crane
for transport.
• Damage must be reported to us immediately.
• The products must not be stored outdoors and must be
protected against moisture.
5.2 General transport requirements
ATTENTION!
Transport must be arranged in compliance with safety
regulations!
• The enclosures DualGuard-S ESF30 US 30P and Dual-
Guard-S ESF30 US 15P are shipped upright on the pallet.
• If the packaging is damaged, the damage must be reported
to the freight forwarder in writing on the shipping ticket – a
"clean receipt" from the delivering freight forwarder excludes
acknowledgement of transportation damage. The same
applies for missing packages pursuant to the shipping ticket.
• Our plates weigh approximately 65 kg per m² of surface
area. Attention: injury risk!
• Open the pallet at the installation location only to prevent
damage while in transit to the installation location.
• When opening the pallets, the enclosure can be damaged
when pointy or sharp objects, such as knives are used.
Please use caution!
• Dispose of or reuse packaging materials in an environmen-
tally compliant manner.
• If the fire protection enclosure is not immediately used or
installed, it needs to be stored in an appropriate location.
Ensure that spray water cannot form or penetrate – do
not store outdoors.
• Fire protection enclosures have an integrated base with
fork pockets. The front cover must be removed for use.
• Transport must be arranged in compliance with safety
regulations!
• Move the enclosure upright on the transport pallet.
• Only remove the tie-downs at the setup location.
• If the enclosure needs to be laid down, only place it on the
full back or side surfaces in a jerk-free manner.
• Do not lay the enclosure down on its door(s)!
• The enclosure must be locked when doing this.
• Note the considerable weight of the fire protection en-
closure.
ATTENTION!
Any damage to the equipment must be immediately reported
to us in writing!
The recipient is responsible for the receiving inspection
The shipped product and its packaging must be promptly
inspected for damage, completeness, and other anomalies.
Any identified damage must be immediately documented
(sketch, photo, description, etc.) and submitted to CEAG
Notlichtsysteme GmbH.
Unpacking
The packaging must be disposed of in an environmentally
friendly manner.
Intermediate storage
If the enclosures are not used or installed immediately,
they need to be carefully stored in a protected location. The
enclosures must not be stored outdoors.
6 Assembly/installation
DualGuard-S ESF30 30-P and 15-P
6.1 Assembly/installation
Check the fixing accessories supplied for complete-
ness:
- 2 Hanging brackets
- 1 two-way (double bit) key
- 10 countersunk screws
- 2 Senkkopfschrauben 6,0x120
6.2 Opening and closing the door(s)
Opening:
• Insert the key into the lock.
• Turn the key clockwise by a quarter-turn and pull out
twist lever.
• Turn twist lever upwards through 180° anticlockwise.
• Open the door.
Closing:
• Close the door and ensure that the twist lever is open.
• Press the door gently and turn twist lever downwards
through 180° clockwise.
• Allow the twist lever to audibly latch back into the twist
lever holder.
• Remove the key.
