background image

34

Instruction Book    

IB182942EN   July 2018   www.eaton.com

DST-2-VR

+

VR-Series

+

 Replacement Circuit Breaker

Tablt 6.3. Troubltshooting Chart

SYMPTOM

INSPECTION AREA

PROBABLE DEFECTS

FAILS TO CLOSE

Closing Springs Not Charged

Control Circuit

• Control Power (Fuse blown or switch off)
• Secondary Disconnect Contacts
• Motor Cut-off Switch (Poor or burned contacts. Lever not operational.)
• Terminals And Connectors (Poor or burned contacts)
• Motor (Brushes worn or commutator segment open)

Mechanism

• Pawls (Slipping or broken)
• Ratchet Wheel (Teeth worn or broken)
• Cam Shaft Assembly (Sluggish or jammed)
• Oscillator (Reset Spring off or broken)

Closing Springs Not Charged

Circuit Breaker Does Not Close

Control Circuit

(Close Coil does not pick up)

• Control Power (Fuse blown or switch off)
• Secondary Disconnect Contacts
• Anti Pump Relay (Y Relay N.C. contact open or burned or relay picks up)
• Close Coil (Open or burned)
• Latch Check Switch (Contact open - Bad switch or trip bar not reset)
• Auxiliary Switch (B Contact open or burned)
• Motor Cut-Off (Contacts open or burned)
• Trip Coil Assembly (Clapper fails to reset)

Closing sound but no close

• Pole Shaft (Not open fully)
• Trip Latch Reset Spring (Damaged or missing)
• Trip Bar-D Shaft (Fail to remain reset)
• Trip Latch-Hatchet (Fails to remain reset)
• Trip Floor Tripper (Fails to remain reset)
• Close Latch (Binding)
• Close Latch Roller (Binding)
• Trip Circuit Energized

UNDESIRABLY CLOSES

Control Circuit

• Close Circuit (CS/C getting shorted)

Mechanism

• Close Release Latch (Fails to reset)
• Close Floor Tripper (Fails to reset)

FAILS TO CLOSE

No Trip Sound

Control Circuit

• Control Power (Fuse blown or switch off)
• Secondary Disconnect Contacts
• Auxiliary Switch (A contact not making poor or burned)
• Trip Coil (Burned or open)
• Terminals and connections (Poor or burned or open)
• Trip Clapper (Jammed)

Trip Mechanism

Trip Sound But No Trip

Trip Mechanism

• Trip Bar, Trip Latch (Jammed)
• Pole Shaft (Jammed)
• Operating Rod Assembly (Broken or pins out)

Vacuum Interrupter (One Or More Welded)

UNDESIRABLY TRIPS

Control Circuit

• Control power (CS/T Switch, remains made)

Mechanism

• Trip Coil Clapper (Not resetting)
• Trip Bar or Trip Latch (Poor engagement of mating or worm surfaces)
• Trip Bar Reset Sprint (Loss of torque)

Summary of Contents for DST-2-15-500





































Reviews: