3
Wire Combination
Torque
#12 with #14
12 in-lbs
#14 with #16
12 in-lbs
#16 with #18
12 in-lbs
#16 with #20
12 in-lbs
#16 with #22
12 in-lbs
#18 with #22
10-12 in-lbs
#18 with #20
10-12 in-lbs
#20 with #22
7-12 in-lbs
Table C
Follow the schematic (Figure 6) to wire the 2 and 3-wire
control modules.
Note: For 2-wire control, ensure the two wires coming from
the control module are connected across a NC auxiliary
contact.
Figure 6
5 COIL
KITS
5.1 Description
A wide range of coils is available for both electrically held and
mechanically held lighting contactors. Refer to the
Ordering
Detail
section for more information about the coil kit catalog
numbers and voltages available.
Note: For mechanically held lighting contactor, only use coil
rated up to 277 VAC maximum. Use control power
transformer for higher voltages.
5.2 Installation
1. Disconnect all power. Replace and mount the coil on the
contactor as shown in Figure 7.
2. For mechanically held contactors, remove all wires from
the control module and remove the coil cover
along with
control module
.
5.3 Wiring
Coil terminal can accept wires from #18 AWG to #14 AWG
(either solid or stranded) as single or combination of two wires
(Refer to Table D below for valid wire combination). Wire
material must be copper with a temperature rating of 60 or 75
degrees C. Maximum tightening torque is 15 in-lbs.
Table D
Ordering Details
Coil Kits:
9-3242-7
24V 60Hz / 20V 50Hz Coil
9-3242-8
28V 60Hz / 24V 50Hz Coil
9-3242-1
115-120V 60Hz / 110V 50Hz Coil
9-3242-5
200-208V 60Hz Coil
9-3242-2
230-240V 60Hz / 220V 50Hz Coil
9-3242-6
265-277V 60Hz / 240V 50Hz Coil
9-3242-9
347V 60Hz Coil
9-3242-3
460-480V 60Hz / 440V 50Hz Coil
9-3242-4
575-600V 60Hz / 550V 50 Hz Coil
Control Module Kits:
C320MH2WT0
2 wire 24 VAC 60/50 Hz
C320MH2WA0
2 wire 110-120 VAC 60/50 Hz
C320MH2WH0
2 wire 200-277 VAC 60/50 Hz
C320MH2WT1
2 wire 12-24 VDC
C320MH3WT0
3 wire 24 VAC 60/50 Hz
C320MH3WA0
3 wire 110-120 VAC 60/50 Hz
C320MH3WH0
3 wire 200-277 VAC 60/50 Hz
C320MH3WT1
3 wire 12-24 VDC
Power Pole Kits:
C320PRP1
Single Power Pole
C320PRP2
Double Power Pole
Auxiliary Contact Kits:
Auxiliary Contact Block 1 NO when
mounted on left side of contactor.
C320AMH1
Auxiliary Contact Block 1 NC when
mounted on right side of contactor.
Auxiliary Contact Block 2 NO when
mounted on left side of contactor.
C320AMH2
Auxiliary Contact Block 2 NC when
mounted on right side of contactor.
Note
:
These instructions do not purport to cover all details or variations in
equipment nor provide for every possible contingency to be met in connection
with installation, operation, or maintenance. Should further information be
desired or should particular problems arise which are not covered sufficiently
or the Purchase’s purpose, the matter should be referred to Eaton e-Com
Technical Support. Toll free telephone (800) 356-1243.
Figure 7
# 14 AWG
# 16 AWG
# 18 AWG
Size Type
Solid Stranded Solid Stranded Solid Stranded
Solid X X X X X X
# 14 AWG
Stranded X X X X X X
Solid X X X X X X
# 16 AWG
Stranded X X X X X X
Solid X X X X X X
# 18 AWG
Stranded X X X X X X
Instruction Sheet Pub50765
Revision A Page 3 of 4
DEH-41043
ECR LT#10001
