background image

5

Toxin    |    Installation & Service Manual

Before Starting Installation 

(Cont’d)

PLAN HOW YOU WILL INSTALL THE FILTER

 

»

You must first decide how to run in and out pipes to the filter.  Look at the house main water 
pipe at the point where you will connect the filter.  Is the pipe soldered copper, glued plastic or 
threaded brass/galvanized?  What is the pipe size?

 

»

Determine the direction of the water flow in the home, then turn off incoming water supply valve.  
Plumb the incoming water line into the bypass valve side marked “IN”.  Plumb the line leaving 
the filter into the bypass valve side marked “OUT”.  

PRODUCT INSTALLATION SEQUENCE

Unless special equipment is available to mechanically torque 
the valve to the tank, please follow the steps below:

1) 

Hand spin the valve onto the tank, ensuring the threads 
are not cross-threaded.  

Note: All Fleck valves are right-

hand threads, or clockwise, to install.

2) 

Rotate the valve freely without using force until it comes to a 
stop (this position is considered zero).

3) 

Rotate valve clockwise from zero to between ¼ turn and ½ 
turn (see diagram to the right).

¼ Turn

Tank

Valve

½ Turn

Zero

¼ Turn

Good

Zone

Rotation

½ Turn

Zero

INSTALLING VALVE HEAD ON TANK

DO NOT exceed 25 ft lbs of torque when installing this 
product. Exceeding this limit may damage the threads 
and cause failure.

Note: Do NOT use the drain connector to tighten the valve on the tank.  This can break the 
drain connection or crack the valve.  

Municipal

Water Main

City Water

Water
Pump

Pressure

Tank

Acid

Shield

Acid

Shield

Toxin

Toxin Shield Cartridge

Lead 

Shield

Lead 

Shield

No-Salt Conditioner

1100/2200/3500

No-Salt Conditioner

1100/2200/3500

Bacteria

Shield

Bacteria

Shield

Iron

1000/2000

RevitaLife

RevitaLife

Private Well Water

Summary of Contents for Toxin Shield+ TS+1000












Reviews: