background image

2

Toxin    |    Installation & Service Manual

Unpacking & Inspection

Basic Guidelines

Be sure to inspect the entire shipment immediately upon receipt for any shipping damage or parts 
loss.  Also note any damage to the shipping carton.  

Contact the transportation company for all 

damages and loss claims.  EasyWater is not responsible for damages in transit.

 

»

Before you begin installation, read the entire manual. 

 

»

CHECK LOCAL PLUMBING AND ELECTRICAL CODES. THE INSTALLATION MUST 
CONFORM TO STATED CODES.

  

 

»

Use only lead-free solder and flux for all sweat-solder connections, as required by state and 
federal codes.

 

»

Use care when handling the filter.  Do not drop or set on sharp objects.

 

»

Do not locate the system where freezing temperatures occur.  Do not attempt to treat water that 
is over 120°F.  

FREEZE DAMAGE OR HOT WATER DAMAGE VOIDS THE WARRANTY.

 

»

If installing outdoors, protect from direct sunlight.  Excessive sun and heat may cause distortion 
or other damage to non-metallic parts.

 

»

While the electronic components, protect the filter if installing it outdoors where water damage 
can occur.

 

»

Unplug the filter from electrical power before servicing the filter or removing the outer valve 
cover.  Complete maintenance or repairs and replace covers before plugging into the power 
outlet again.

 

»

The filter works on 120V – 60 Hz electrical power only.  

MAKE SURE THE FILTER IS PLUGGED 

INTO AN OUTLET WITH CONTINUOUS POWER.

Summary of Contents for Toxin Shield+ TS+1000












Reviews: