3.If I forget the password I set, how to re-set it again?
Please refer to d.password reset instructions on page 39-40 in user manual.
4.When I attempt to start the car, it start but shut off a few seconds, what’s the reason?
There are possible 4 reasons:
A.The blue fuel pump wire in 20 Pin wire harness not connect well which lead to there is no electricity when
you want to start the vehicle. The fuel pump wire is recommend to connect with the fuel pump wire or oil
pump wire /oil path motor /sucker motor/ in the vehicle, if you can't find these wire in the vehicle, you can
connect it with the co12 wire or tach wire.
B.The starting time is not enough. If so, you need to prolong the starting time. For detailed instruction,
please refer to engine cranking time in parameter time prolong setting in the user manual.
C.Please check whether the yellow starter wire in 6 Pin wire harness is well connected
D.If there is chip immobilizer in your vehicle factory key fob, you should add an extra bypass module, please
make sure the bypass module is well installed and connected in order that you can start your vehicle.
5.I am not able to use remote engine start function, what’s the reason?
Please check if the blue fuel pump wire in 20 Pin wire harness is correctly connected or not.
The alarm default setting is for auto gear car and switch 5 in the control module is press down. If your
vehicle is manual gear car and you want to use remote engine start function, please press up the switch 5 in
power off status (that’s un-plug the 6P ignition wire harness from the control module, then press up Switch
5, then re-plug the 6P ignition wire harness with the control module), and set it to manual gear car shift first.
Once the kit is set to manual gear car shift, driver goes out of the vehicle and close doors without flameout,
walk away from the vehicle for at least 8 meters, keep pressing the start button on the remote control for
around 3 seconds to shut down the vehicle. After that, the user can use remote engine start function for
manual gear car.
The hand brake should be in neutral position when use the remote start function for a manual gear car.
User also can refer to the info of remote start for manual gear car in the user manual.
6.Does the device has anti-hijacking function?
Yes, The alarm default setting is with anti-hijacking function and DIP switch 4 in the control module is press
down, if you do not want this function, please press up the DIP switch 4 in the control module in power off
status.
7.The DIP switch 4 in the control module is press down, but I still not able to use anti-hijacking
function, why?
Please check:
A.If you press down DIP switch 4 on control module in power off status( that’s unplug the 6P ignition wire
harness from the control module first, then press down DIP switch 4 on control module, then re-plug the 6P
ignition wire harness with the control module. If not, please correct the setting.
B. whether the blue/black door trigger wire is well connected, which default setting is negative (-) and can be
re-set with jumper on it to be positive (+), for detailed instruction, please refer to note 10 in user manual.
8.How to do programming?
Please refer to programing method in the user manual.
9.How to wire the 3 color (orange, yellow & white) GWR wire?
Please refer to Note 8 in the user manual.
10.How to set the device to valet mode?
Please refer to the valet mode on/off in the user manual.
11.When I open the door, I heard the control module is sound click sometimes, but when I close the
door, it’s normal, is this a defective product?
No. When you opening the vehicle door, the relay in the control module need to work and will sound click for
a few seconds and this is normal. And when you close the door, the clicks will stop accordingly as the relay
is not in working status.
12.What’s the usage of DIP Switch 6 in the control module?
The switch 6 is for return current. For some vehicles, need to turn the key to ON position first then the foot
brake is with electricity when stepping on it. For this kind of cars, need to press down the DIP switch 6. For
some types of
Volkswagen (VW) cars, even all the wires are correctly connected, but still unable to unlock
car doors when press unlock button , if so, please un-plug the 6 pin ignition wire harness from the control
module, press down DIP switch 6, then re-plug the 6P ignition wire harness with the control module, now
everything is working well now. The switch 6 is mainly for some Volkswagen cars usage.
13.Is there a GWR (ground while running) wire? Or how to connect with a GWR wire to the EC002?
Please refer to note 8 for the GWR wire connection method.
14.How to connect a window closer module with your alarm?
If there is window closer module need to connect with EC002 alarm, please connect the wire from window
closer module with white locking wire in central door locking wire.
15.I turn on PKE function then start the car, but when I stop and cut off the engine, the PKE function
is automatically turn off and I have to turn it on again, what’s the reason?
The problem should due to the blue/black door trigger wire(-) is not well connected.
Warning:
This product is intended to be installed by a professional car alarm installer only! Any attempt to
install this product by any person but not a trained professional car alarm installer may result in severe
damage to the vehicle or the components.
16.I hook up the door trigger wire, but when opening car door, turn signal light flashes, what’s the
reason?
If so, please disconnect the door trigger wire first, unplug the 6P ignition wire harness from the control
module, then press down DIP switch 2, re-plug the 6P ignition wire harness with the control module.
17.Why there is no orange, white and yellow wire in my kit?
If the alarm is equip with shock sensor, then there is no orange, white and yellow 3 color GWR wire and you
can use an extra SPST relay to generate a GWR wire, for detailed instruction, please refer to Note 9 in the
user manual.
Warranty information
The quality of this product is strictly controlled before out of the factory, which ensure its advanced
performance under normal utilization. And we provide 1 year quality guarantee. If there is any failure due to
product quality, we will provide free repair or replacement. Any incorrect operation / installation / using lead
the product was failed to work is not in cover of free repair or replacement service.
-44-
©
EASYGUARD
Electronics
.
All
right reserved.
-43-
©
EASYGUARD
Electronics
.
All
right reserved.
