background image

 

6

 
D)

 

Gain assurance from a responsible person that the Industrial Truck and combination of 
attachments  which  are  used  to  support  the  platform,  comply  with  AS  2359.1  and  that 
person  has  provided  all  information  necessary  to  ensure  that  risks  are  eliminated  or 
controlled. 

E)

 

Do not exceed the rated capacity of the Industrial Truck to handle the load. Trucks used 
to lift the type WP Work Platforms must have capacities equal to or greater than; 

 

For a counterbalance truck – 1825 kg, 

 

For reach trucks – 1095 kg. 

F)

 

The  Industrial  Trucks  shall  be  used  on  a  hard  level  surface.  The  area  in  which  the 
attachment  is  to  be  used  has  been  accessed  as  suitable  for  the  task  to  be  undertaken. 
There should be suitable clear space to safely use the Work Platform. 

G)

 

While lifting in an area subject to passing traffic, barriers or warning signs shall be used 
to prevent any interference. 

H)

 

Any stabilisers on the Industrial Truck shall be engaged prior to lifting. 

I)

 

The travel controls shall be in neutral with the park brake engaged. 

J)

 

The mast, if adjustable shall be set at vertical, NOT back tilted. 

K)

 

The Fork Arms shall be horizontal. 

L)

 

The controls, other than the tilt, lifting and lowering controls, shall be immobilised. 

M)

 

The  Operator  and  every  person  to  be  elevated  shall  check  the  Platform  is  securely 
attached to the Forklift in accordance with these Instructions – 

refer Section (3.1)

N)

 

The Operator shall stay with the Industrial Truck controls at all times. 

O)

 

The Operator shall keep hands and feet clear of controls other than controls in use. 

P)

 

The  Operator  shall  keep  clear  of  overhead  obstructions  and  in  particular

         

MAINTAIN RELEVENT CLEARANCE OF ELECTRICAL CONDUCTORS.

 

Q)

 

Before any person is elevated or supported by the Work Platform, the Operator shall lift 
the platform to the required working height to confirm that all systems are functioning 
correctly. 

R)

 

The Operator shall lift and lower the platform in a smooth manner. 

S)

 

Elevated personnel shall stand on the floor of the platform at all times they are elevated. 

T)

 

Ladders or any other means shall not be used to gain extra height. 

U)

 

Whenever  a  person  is  supported  by  the  platform,  any  manoeuvring  of  the  Industrial 
Truck shall be minimised. 

V)

 

Ensure safety features are provided, visible and working effectively. 

W)

 

Ensure  no  unauthorised  alterations  to  the  equipment  have  been  made  that  may  cause 
risk.  

X)

 

Ensure  regular  maintenance,  testing  and  inspections  are  carried  out  and  recorded  in 
accordance  with  the  relevant  Industrial  Truck  Manuals  and  these  instructions 

[refer 

Section (7)],

 and corrective action initiated where applicable. 

Y)

 

If  any  of  the  equipment  becomes  unsafe,  stop  all  usage  until  the  risk  is  eliminated  or 
controlled 

Z)

 

The  Industrial  Truck  is  to  be  operated  in  accordance  with 

AS  2359.2  Section  (3)

  and 

these Instructions where applicable. 

 
 

WARNING

:  Failure  to  observe  the  above 

Risk 

Control  Measures

  and  those  outlined  in 

Appendix  A

 

could result in 

SERIOUS INJURY or DEATH. 

 
 
 
 
 

Summary of Contents for WP












Reviews: