background image

 

5

 

WARNING

:  In  some  states  of  Australia,  the  use  of 

Work  Platforms  must  be  approved  by  the  statutory 
Authority.  The  type  WP  Work  Platform  is  designed  to 
carry a maximum of two (2) people or a SWL of 250kg 
and is for approved use only.

 

 

Operator Qualifications and Authorization 

 
The qualification of the operator shall be in accordance with AS 2359.2 clause 2.1 that covers 
age,  physical  disabilities,  training,  fluency  of  the  English  language  for  communication, 
adequate knowledge of this standard and conformance to the relevant Statutory Authority.  
 
The  Authorization  of  the  Operator  shall  be  in  accordance  with  AS  2359.2  clause  2.3.    This 
covers three sections of operating procedures as follows;  
 

 

Section  3

  that  covers  general  operating  procedure’s  as  stated  in  the  “Risk  Control 

Measures – Summary” section (5), paragraph “Z)” below,  

 

 

Section  4

,  which  cover  procedures  for  particular  machines  i.e.  elevating  operator  or 

automatically controlled industrial trucks, 

 

 

Section  5

,  which  cover  procedures  for  site  conditions  i.e.  hazards,  explosive  and 

flammable  atmospheres,  pedestrian  access,  warning  signs,  warning  devices,  guards, 
lighting,  noise  levels,  atmospheric  pollution,  service,  ground  and  floor  surfaces, 
inclines, aisles, loading docks, bridgeplates and dockboards and lifts.  

 
 

5) 

RISK CONTROL MEASURES – SUMMARY 

 
When  handling  loads,  the  Risk  Control  Measures  outlined  below  in  Sections  (5)  are  to  be 
observed by the Industrial Truck Operator to ensure all identified hazards relative to using this 
equipment are eliminated or controlled – 

refer Appendix A for a detailed analysis

 
A)

 

The  Industrial  Truck  Operator  requires  a  suitable  forklift  licence  to  cover  both  the 
Industrial Truck being operated and the Work Platform that has been fitted. Training in 
the safe use of the Work Platform shall be undertaken before use. 

B)

 

The use of the Work Platform shall be limited to those situations where it is necessary 
to  elevate  personnel  to  perform  special  tasks  of  short  duration  and  where  it  is  not 
possible to use scaffold or a specially designed device. The platform shall not be used 
for order picking, nor for production or stores types of activity. 

C)

 

Authorised  personnel  must  perform  the  following  pre-checks  immediately  prior  to  the 
use  of  the  Industrial  Truck  in  accordance  with  AS  2359.2  clause  3.1  and  6.4  and 
corrective action initiated where applicable; 

 

Nameplate  and  markings  regarding  the  Industrial  Truck  and  Attachment  capacities 
are to be read and acknowledged, 

 

Condition of lift and tilt systems on the Industrial Truck to be checked, 

 

Inspect all tyres for wear, condition and pressure if applicable, 

 

Liquid  levels  of  battery  cell  electrolyte,  oils  (hydraulic,  engine,  transmission  and 
brake), cooling water and fuel to be checked, 

 

All  steering  and  brake  controls,  warning  devices  and  lights  to  be  checked  for 
effective operation. 

Summary of Contents for WP












Reviews: