background image

7

Read the entire manual carefully before installing 

and operating the product. Observe the following 

instructions:

Safety instructions for the installation

—   This product shall only be installed, repaired or 

serviced by an authorised electrician. All applicable 

local, regional and national regulations for electrical 

installations must be respected.

—   Danger to life due to high electrical voltage. Never 

make any changes to components, software or 

connecting cables.

—   The installation must not be carried out in the vicinity 

of explosive atmospheres or in areas where there is a 

risk of flowing water.

—   The product must be installed on a permanent 

location. The connections of the Chargeberry and 

backplate are designed for a limited number of 

plugging cycles.

—   The product must be installed on a wall or structure 

with sufficient load bearing capacity. 

—   The charger should always be installed on a surface 

that covers the entire back side area of the product.

—   The terminals in the backplate are energised when 

the power circuit is closed and must never be in direct 

contact or in contact with anything other than the 

plug-in electronics (Chargeberry).

—   The PIN code is located on the front of the 

Chargeberry and is required for installation. After 

installation, paste the PIN code on the back of the 

manual or in a safe place, e.g. inside of the fuse 

cabinet door.

Safety instructions

Safety instructions for operation

—   Danger to life due to high electrical voltage. Never 

make any changes to components, software or 

connecting cables.

—   Never use or touch the product if it is damaged or 

does not function properly. 

—   Always have the prescribed maintenance, installation 

and any repair work carried out by an authorised 

electrician and in accordance with local requirements.

—   If a fire occurs, do not use water for extinguishing. 

Never clean the Charging Robot with high pressure or 

running water.

—   Do not immerse the product in water or other liquids.

—   If the light strip on the product lights up red, there is a 

fault. For more information, see page 19.

—   Make sure that children do not play with the product.

—   Never touch the contacts of the Type 2 socket and 

never insert foreign objects into the product.

—   Never use the charging cable if it is damaged or if the 

connections are wet or dirty.

—   Do not use extension cords or unapproved adapters 

in combination with the product.

—   Never bend or run over the charging cable with a car 

or expose it to excessive heat.

—   The charging cable must only be removed from the 

Charging Robot by pulling the plug handle as close 

to the Charging Robot as possible, not by pulling the 

cable.

—   Do not place the charging cable in the path of other 

road users. Always position it in such a way that 

there is no risk of tripping.

—   Even if the Charging Robot is designed to withstand 

normal weather conditions, we recommend 

protecting it from direct sunlight or exposure to 

extreme weather conditions. Never connect the 

charging cable to the Charging Robot when the cable 

connector is wet.

—   Do not use the product near strong electromagnetic 

fields or in the direct vicinity of radio transmitters.

Summary of Contents for Home

























Reviews: