background image

SCW-410-QS (05/12) 

 

Page 13 

Antifreeze Protection 

When 

SCW compressor units 

are applied to radiant panel hydronic heating and/or chilled water 

cooling systems, the water circulating system must be protected from potential damage due to 
freeze-up by utilizing an adequate antifreeze solution. The antifreeze protection is provided by the 
installer prior to the EarthLinked

®

 system start-up. 

 

Propylene-glycol antifreeze solution with an inhibitor is the type of antifreeze solution required for 
Earthlinked

®

 products utilized in radiant panel hydronic heating and/or chilled water cooling 

systems. These systems shall be freeze protected consistent with the application -specific 
minimum temperature, as shown in the table below. Propylene-glycol antifreeze solutions should 
always be in the range of 20% to 50% by volume, as indicated in the table. 

 

TEMPERATURE, °F 

PROPYLENE GLYCOL, % 

WATER SOLUTION 

MULTIPLIER FACTOR (WSMF) 

18 

20 

x 1.03 

30 

x 1.07 

-7 

40 

x 1.11 

-29 

50 

x 1.16 

 Propylene Glycol Freeze Protection Table 

 

 

Propylene-glycol can be purchased in the straight form and mixed with an inhibitor prior to filling 
the system, or it can be purchased as inhibited propylene-glycol. The following are examples of 
manufacturers for the above: 

 

Straight propylene-glycol: Chemical Specialties, Inc. (

www.chemicalspec.com/spg.html

) 

Inhibitor: Nu-Calgon Products, Ty-lon B20  (

www.nucalgon.com/products

 

Inhibited propylene-glycol: Houghton Chemical Corp., SAFE-T-THERM

®

www.houghton.com/fluids/safe-t-therm/index.html

 

 

Summary of Contents for SCW Series































Reviews: