background image

SCW-410-QS (05/12) 

 

 

 

 

 

Disclaimer 

Proper installation and servicing of the EarthLinked

®

 Heating and Cooling System is essential to its 

reliable performance. All EarthLinked

®

 systems must be installed and serviced by an authorized, 

trained technician who has successfully completed the training class and passed the final 
examination. Installation and service must be made in accordance with the instructions set forth in 
this manual and the current 

EarthLinked Heating and Cooling Systems Installation, Operation and 

Maintenance Manual.

 Failure to provide installation and service by an authorized, trained installer 

in a manner consistent with the subject manuals will void and nullify the limited warranty coverage 
for the system. 

READ THE CURRENT EarthLinked Heating and Cooling Installation, Operation and 
Maintenance Manual
 FOR COMPLETE INSTALLATION DETAILS. 

Earthlinked

 

Technologies shall not be liable for any defect, unsatisfactory performance, damage or 

loss, whether direct or consequential, relative to the design, manufacture, construction, application 
or installation of the field specified components. 

 

 

Earthlinked Technologies, Inc. 

4151 South Pipkin Road 

Lakeland, Florida 33811 

tel. 863-701-

0096 ● fax 863-701-7796 

info@earthlinked

.com ● 

www.earthlinked.com

 

CSI # 23 80 00 

Summary of Contents for SCW Series































Reviews: