background image

The 230V unit will operate for approximately
1 1/2 hrs and the 110V unit will operate for
approximately 3 1/4 hrs before requiring
refilling. The water level is shown through
the glass level indicator and should not be
allowed to fall below minimum. Switch the
unit off when this level has been reached.
If you require further use of the steamer,
ensure unit is switched off and has stopped
boiling. Wait for 5 minutes. Slowly unscrew
the cap, any remaining trapped steam will
be released from beneath cap. 

Caution -

steam is very hot -wear a glove and keep
face clear.

Refill to the level indicator as

before and follow above instructions.

YOU MUST NEVER ALLOW THE UNIT TO
BOIL DRY.

There is a safety thermal cut-out device
fitted to the unit. If the unit is allowed to boil
dry this will operate and prevent further use.
Switch the unit off and allow it to cool for at
least 5 minutes, refill with water and then
switch on again - the thermal cut-out should
automatically re-set. If this has not re-set
allow a further cooling period.
When you have finished using the unit allow
any remaining water to cool and then empty
the unit. We recommend flushing the tank
out with clean water before storing. NEVER
LEAVE WATER IN THE UNIT WHILST
BEING STORED.

Storage Spools

These are designed for easy and compact
storage. The mains lead and hose must be
fully unwound before commencing to
operate the unit.
To recoil the mains lead: Fit the plug into the
socket on the side of the spool and then
wind the mains lead onto the spool.

To recoil the hose: Place the steam plate
end of the hose into the side aperture of the
spool and then wind the hose onto the
spool.

Storage Steam Plate

The handle of the steam plate is shaped to
locate between the frame and the tank.
Slide the plate into position with the handle
against the tank and the thread towards the
base.

Filler Cap

To fit - screw onto the filler neck hand tight.
Do not overtighten.
To remove - ensure unit is switched off and
has stopped boiling. Wait for 5 minutes.
Slowly unscrew the cap, any remaining
trapped steam will be released from
beneath cap. 

Caution - steam is very hot -

wear a glove and keep face clear.

Refill to

the level indicator as before and follow
above instructions.
DANGER FROM STEAM.

4

Summary of Contents for Steam Master LMB110V









Reviews: