background image

l

CAUTION: TO REDUCE THE 

RISK OF ELECTRIC SHOCK 

OR INJURY, DO NOT EXPOSE

TO RAIN. STORE INDOORS.

l

The substances used with this 

spray gun may contain 

hazardous, harmful, explosive 

or corrosive materials. ALWAYS

COMPLY WITH THE SAFETY 

INSTRUCTIONS ISSUED WITH 

THIS PRODUCT AND THE 

MATERIAL BEING USED

.

l

The spray gun must only be 

used with paints that have a 

suitable flash point for 

spraying. If in doubt, consult 

the paint manufacturer's data.

l

Always ensure there is 

adequate ventilation when 

spraying.

l

NEVER spray near an open 

flame, including an appliance 

pilot flame.

l

NEVER smoke whilst spraying.

l

Always disconnect the unit 

from the power supply when 

re-filling the paint container.

l

Always disconnect the unit 

from the power supply when 

cleaning the spray gun.

l

Always ensure the spray area is 

safe and free from all debris 

that may present a fire or trip 

hazard.

l

NEVER under any 

circumstances point the spray 

gun at another person or 

animal. In the event of injury 

occurring, seek expert medical 

advice immediately.

l

NEVER allow children or 

unauthorized users to operate 

or play with the spray 

equipment.

l

Always read the paint 

manufacturer's thinning 

instructions before use.

l

Always wear the correct 

protective face mask when 

spraying. We also recommend 

wearing gloves, goggles and 

overalls.

l

After every use ensure that 

you clean the spray gun 

thoroughly and grease the 

gland seal.

l

Use only genuine Earlex 

replacement parts.

l

If the supply cord is damaged, 

it must be replaced by Earlex 

or its appointed agents to 

avoid a hazard.

l

Only use the spray equipment 

as detailed in these 

instructions.

l

Do not use the air hose or 

power cord to pull the HVLP 

turbine unit.

l

Check the hoses, hose 

connectors and power cord 

daily. Any worn or damaged 

parts should be replaced 

immediately.

l

This appliance is recommended

for household   use only.

l

This appliance can be used by 

children aged from 8 years 

and above and persons with 

reduced physical, sensory or 

mental capabilities or lack of 

experience and knowledge if 

they have been given 

supervision or instruction 

concerning use of the appliance

in a safe way and understand 

the hazards involved. Children 

shall not play with the 

appliance. Cleaning 

and user maintenance 

shall not be made 

by children without 

supervision.

WARNING! FIRE AND EXPLOSION HAZARD.

3

SAFETY INSTRUCTION

S

Summary of Contents for CHV512

















Reviews: