background image

EXTENSION CORDS

Your Create by Earlex™ Craft Paint Spraying Kit is supplied with a power cord that is 6 feet long.

Make sure your extension cord is in good condition. When using an extension cord, be sure to

use one heavy enough to carry the current your product will draw. For lengths up to 50 feet,

0.75mm extension cords should be used. For lengths over 50 feet 1mm or heavier should be

used. 

DOUBLE-INSULATED APPLIANCE

This is a double-insulated appliance and as such, does not require three-way earthing. 

SERVICING OF A DOUBLE-INSULATED PRODUCT

In a double-insulated product, two systems of insulation are provided instead of earthing. No

earthing means is provided on a double-insulated product, nor should a means for earthing be

added  to  the  product.  Servicing  of  a  double-insulated  product  requires  extreme  care  and

knowledge of the system, and should be done only by qualified service personnel. Replacement

parts for a double-insulated product must be identical to those parts in the product.

A  double-insulated  product  is  marked  with  the  words  “DOUBLE  INSULATION”  or  “DOUBLE

INSULATED.” 

The symbol 

may also be marked on the product to denote such.

4

1.

400W Turbine Unit

2.

Craft Spray Gun with 1.0mm needle

(see accessory list for extra needles)

3.

Air Hose   
(L0543)

4.

5 Stencils

(L1950)                      

5.

Masking Tape
(L1955)

6.

250ml Pot

(CHVAC01)

7.

Paint Stirrer

(L1565)

8.  

DVD

(L1953)

What

s in the box?

Important Electrica

l Information

DVD

Summary of Contents for CHV512

















Reviews: