Eagle EI-1000 Setup, Calibration And Troubleshooting Download Page 38 | Manualshive

Page: 38 / 44

background image

PORTS & JUMPERS

P1

BDM interface

Factory use only – Do not connect anything to this header.

P2 (J7)

Display interface

This connects, via ribbon cable, to the display, which are the
DSP1000 (EI-1000) and EI-2000-DSP.

P3 & P4

Expansion board

interface

Both headers are used to connect to expansion boards,
which are the EI-2000-IO and EI-2000-EXP.

J1 & J2

Sense connections Local or remote sense selection shunts.

J3

Instrument

selection

This selects an EI-1000, EI-2000 or EI-4000 instrument, see
below.

This is set at the factory, and if this jumper is not

set properly, the meter will not function.

J4

RS485 terminator

resistor

Install a shunt to connect the 120 ohm terminator resistor to
the RS485 A & B lines.

FUSE

The fuse is a ½ ampere, 250VAC, 5x20mm, time-lag fuse.

Do not use any other rating.

VOLTAGE SELECT SWITCH (S2)

The voltage selection switch, located on the EI-2000S-CPU, selects the 115V or 230V range.

EI-1000 & EI-2000 METER SELECTION HEADER SHUNT (J3)

Connect J3-3 and J3-4 to select an EI-2000 meter; the display is the EI-2000-DSP.

Connect J3-1 and J3-2 to select an EI-1000 meter; the display is the DSP1000.

Invalid shunt positions:

REMOTE SCALE SENSE

Single channel EI-100

e remote sense conn

error of the cable voltage drop, minute thermal errors of the connections and wire
temperature coefficients. The remote sense must be used if intrinsically-safe barriers are
being used. Do not use remote sense on the EI-2000 meter or EI-1000 multi-channel
applications.

Disabled (local sense)

Enabled (remote sense)

0 meters can utilize th

ections. This minimizes the

NOTE: DO NOT SELECT THE VOLTAGE WHILE THE METER IS POWERED!

«
...
36
37
38
39
40
...
»

Summary of Contents for EI-1000













































Reviews:

No comments

Related manuals for EI-1000

Brand: OFFCARR Pages: 12

Brand: OEM Tools Pages: 4

Brand: XP-PEN Pages: 3

Brand: Xblitz Pages: 16

DS-KABD8003-RS3

Brand: HIKVISION Pages: 3

Brand: Fisher-Price Pages: 6

Brand: Gared Sports Pages: 12

Brand: Camtree Pages: 3

Brand: National Cycle Pages: 2

Brand: Raceface Pages: 9

Brand: Nolan Pages: 24

Brand: Subal Pages: 36

Brand: Bioenno Power Pages: 2

Rocky Mountain-EXP SB-1

Brand: Wolfman Pages: 7

Brand: ULTIMATE SPEED Pages: 6

Cinema Mirror HC 37.53

Brand: AVR Pages: 9

Brand: Colzer Pages: 8

Brand: König Electronic Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands