background image

 

Installation, Operation and Parts Manual 

                                     

EE62C-35T-E  /  EE62C-42T-E 

                                                                                                                 

 

 

1.5 Potential safety risks 

1.5.1 Main voltage   

I

nsulation damage and other faults may result in accessible components being live.   

Safety measures:   

 

Only ever use the power cord provided or a tested power cord.   

 

Replace wires with damaged insulation.   

 

Do not open the operating unit.   

1.5.2 Risk of injury, danger of crushing 

In the event of excessive vehicle weight, incorrect mounting of the vehicle or on removing heavy object, there is a 
risk of the vehicle falling off or tipping up.   

Safety measures:   

 

The lift is only ever to be employed for the intended purpose.   

 

Carefully study and heed all the information given in Section 1.4.   

 

Observe the warning notices for operation.   

1.6 Noise level   

Noise emitted during operating the lift should be less than 70dB. For your health consideration, it is suggested to place a noise 

detector in your working area.   

 

 

 

 

 

 

 

 

 

 

Summary of Contents for EE62C-35T-E













































Reviews: