manualshive.com logo in svg

EAE DA110, Product Manual, Page: 17 / 22

Share
Download
EAE DA110 Product Manual Download Page 17

Product Manual DA110 

EAE KNX DALI Gateway 

  

       

DA110 R2.0 

©

EAE Technology  

 

 

www.eaetechnology.com  

 

 

Page 16 / 21 

Allow switch on via brightness value 

 

*yes 

    no 

Allow switch off via brightness value 

 

*yes 

    no 

Allow switch on via relative dimming 

 

*yes 

    no 

Allow switch off via relative dimming 

 

*yes 

    no 

“Switch on” and “Switch off” conditions can be defined for brightness value and relative dimming commands 

separately. If these parameters are selected “no”, then it is not possible to switch “on” or “off” the lighting 

fixtures via brightness value (1 byte) or relative dimming (4 bit) objects of the group.

 

 

Fade time 

 

(switch, brightness value and dim commands)

 

jump to…

1 s

…90

 

s

 

 

These parameter defines the fade time for switch, brightness value and relative dimming commands per 

device.

 

 

Brightness value when switch on 

Last switch on value, 5% (13) …*

100% (255) 

This parameter defines the brightness value when a “switch on” command is received over Switch 

communication object.

 

 

 

 

 

Summary of Contents for DA110























Reviews:

No comments