manualshive.com logo in svg

EAE DA110, Product Manual, Page: 15 / 22

Share
Download
EAE DA110 Product Manual Download Page 15

Product Manual DA110 

EAE KNX DALI Gateway 

  

       

DA110 R2.0 

©

EAE Technology  

 

 

www.eaetechnology.com  

 

 

Page 14 / 21 

No 

Function 

Name 

DPT 

Length  Flags 

41 

Switch 

Dali Device 1…64 

1.001 

1 bit 

CWU 

Switch/Status (after change) 

CWTU 

Switch/Status (after request) 

CRWU 

Switch/Status (after change or request) 

CRWTU 

This object is used to switch DALI device 1…64  ON or OFF. 

 

44 

Group 1, Brightness value 

Dali Device 1…64 

5.001 

1 byte 

CWU 

Set brightness value/Status (after change) 

CWTU 

Set brightness value/Status (after request) 

CRWU 

Set brightness value/Status 

(after change or request)

 

CRWTU 

This object is used to set DALI Device 1…64 brightness value (%0…%100). 

46 

Group 1, Relative dimming 

Dali Device 1…64 

3.007 

4 bit 

CW 

This object is used to dimming group 1. The brightness value is changed in the defined direction with the 

parameterized speed. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for DA110























Reviews:

No comments