-
1 3
-
-
14
-
F u n c t i o n C o d e T a b l e
EC670
EC670
F u n c t i o n C o d e T a b l e
A2
-
02
S3 terminal
function
6： Coast to stop 7： Emergency stop
8： Fault reset (RESET)
9： Normally open (NO) input of external
fault
10：Terminal UP 11：Terminal DOWN
12：UP and DOWN setting clear (terminal,
operation panel)
13：Speed control/Torque control switchover
14：Torque control prohibited
15：Speed search start enable
16：Multi-reference terminal 1
17：Multi-reference terminal 2
18：Multi-reference terminal 3
19：Multi-reference terminal 4
20：Terminal 1 for acceleration/decele-
ration time selection
21：Terminal 2 for acceleration/decele-
ration time selection
22：Acceleration/Deceleration prohibited
23：PID ctrl diaable
24：PID pause 25：PID integral pause
26：Reverse PID action direction
27：PID parameter switchover
28：PID target value switchover terminal1
29：PID target value switchover terminal2
30：PID target value switchover terminal3
31：PID feedback value switchover terminal1
32：PID feedback value switchover terminal2
33：PID feedback value switchover terminal3
34：PLC pause 35：PLC status reset
36：Swing enable 37：Swing pause
38：Swing reset
39：Frequency source switchover terminal1
40：Frequency source switchover terminal2
41：Frequency source switchover terminal3
42：Frequency source switchover terminal4
43：Command source switchover terminal 1
44：Command source switchover terminal 2
45：Counter input
47：Length count input
48：Length reset
49：Immediate DC braking
50：terminal pre flux
51: User-defined fault1
52: User-defined fault2
53：UPS mode active
2
1202H
A2
-
08
Characteristic
selection of
terminals S1-4
0000
～
1111
LED-Bits0: S1 terminal
0: effective closing 1: effective opening
LED-Bits1: S2 terminal
0: effective closing 1: effective opening
LED-Bits2: S3 terminal
0: effective closing 1: effective opening
LED-Bits3: S4 terminal
0: effective closing 1: effective opening
0000
1208H
A2
-
03
S4 terminal
function
16
1203H
A2
-
04
S5 terminal
function
17
1204H
A2
-
05
S6 terminal
function
18
1205H
A2
-
06
S7 terminal
function
19
1206H
A2
-
07
S8 terminal
function
53
1207H
A2
-
09
S1-S4 terminal
filtering time
0.00
～
60.00s
This parameter is defined as the size of
filtering the input signal to eliminate the
interference signal. The longer the fil-
tering time is, the stronger the anti-
interference ability is, but the slower the
response speed is; the shorter the filtering
time is, the weaker the anti-interference
ability is, but the faster the response
speed is.
0.10s
1209H
0000
A2
-
10
120AH
0000
～
1111
LED-Bits0: S5 terminal
0: effective closing 1: effective opening
LED-Bits1: S6 terminal
0: effective closing 1: effective opening
LED-Bits2: S7 terminal
0: effective closing 1: effective opening
LED-Bits3: S8 terminal
0: effective closing 1: effective openin
Characteristic
selection of
terminals S5-8
0.10s
A2
-
11
120BH
S5-S8 terminal
filtering time
0
.
00
～
60.00s
Same as P4-08
3
A2
-
12
120CH
Terminal
control
operation mode
0
～
3
0: the terminal with two-wire system 1
terminal set as 1 is in forward running,
terminal set as 2 is in reverse running,
1：the terminal with two-wire system 2
terminal set as 1 is in starts running,
terminal set as 2 is switch forward and
reverse
2:the terminal with three-wire system 1
terminal set as 1 is in forward running,
terminal set as 2 is in reverse running,
terminal set as 3 is stop running,
3: the terminal with three-wire system 2
terminal set to 1 starts running,
terminal set as 2 is switch forward and
reverse,
terminal set as 3 is stop running,
37
A2
-
13
120DH
Y1 terminal
function
0
～
39
0 ：No output
1 ：AC drive Forward running
2 ：AC drive Reverse running
3 ：Fault output1（no output at auto reset
period ）
4 ：Fault output2（output at auto reset
period ）
5 ：Ready for RUN
6 ：Frequency reached
7 ：Frequency-level detection FDT1 output
8 ：Frequency-level detection FDT2 output
9 ：Frequency upper limit reached
10：Frequency lower limit reached
11：Current 1 reached
12：Current 2 reached
13：Zero current state