E2S D1xS1 Series, Instruction Manual

Page: 10 / 20

E2S Warning Signals
Impress House, Mansell Road, Acton, London W3 7QH sales@e2s.com e2s.com D190 - 00 - 001 - IS - UL Issue B 27/10/2021
FIRE INSTRUCTION & SERVICE MANUAL
D1xS Sounder UL464 / CAN/ULC - S525 Fire
Models: D1xS1 - DC024 - A. D1xS2 - DC024 - A,
D1xS1 - DC024 - S. D1xS2 - DC024 - S,
• - 55°C to +85°C / - 67°F to +185°F
•
Units can be mounted using at least 2 of the 3 - off ø7mm holes in the mounting bracket.
•
D1xS1RDC024 - A & D1xS1RDC024 - S are approved for use as an audible signal appliance for fire alarm use – Public Mode (UL464 &
CAN/ULC - S525) and produce a minimum sound pressure level of US: 81.62dB(A); CA: 84.8dB(A) at 10 feet, (figures @ worst case
11.5Vdc).
•
D1xS1RDC024 - A & D1xS1RDC024 - S produce a minimum sound pressure level of US: 83.4dB(A); CA: 86.4dB(A) at 10 feet (@24Vdc)
•
D1xS1FDC024 - A & D1xS1FDC024 - S are approved for use as an audible signal appliance for fire alarm use – Public Mode (UL464 &
CAN/ULC - S525) and produce a minimum sound pressure level of: US: 92.06dB(A); CA: 98.2dB(A) at 10 feet, (figures @ worst case
11.5Vdc).
•
D1xS1FDC024 - A & D1xS1FDC024 - S produce a minimum sound pressure level of: US: 94.62dB(A); CA: 100.9dB(A) at 10 feet
(@24Vdc)
•
D1xS2FDC024 - A & D1xS1FDC024 - S are approved for use as an audible signal appliance for fire alarm use – Public Mode (UL464 &
CAN/ULC - S525) and produce a minimum sound pressure level of P1: US: 93.56dB(A) / P2: US: 94.9dB(A); CA: 101.6dB(A) / P3: US:
95.51dB(A); CA: 101.8dB(A) at 10 feet, (figures @ worst case 11.5Vdc).
•
D1xS2FDC024 - A & D1xS2FDC024 - S produce a minimum sound pressure level of P1: US: 95.64dB(A) / P2: US: 98.42dB(A); CA:
105.2dB(A) / P3: US: 102.7dB(A); CA: 109.4dB(A) at 10 feet (@24Vdc)
•
D1xS2HDC024 - A & D1xS2HDC024 - S are approved for use as an audible signal appliance for fire alarm use – Public Mode (UL464 &
CAN/ULC - S525) and produce a minimum sound pressure level of P2: US: 95.51dB(A); CA: 103.8dB(A) / P3: US: 96.24dB(A); CA:
105dB(A) at 10 feet, (figures @ worst case 11.5Vdc).
•
D1xS2HDC024 - A & D1xS2HDC024 - S produce a minimum sound pressure level of P2: US: 100.2dB(A); CA: 108.5dB(A) / P3: US:
103.5dB(A); CA: 111.6dB(A) at 10 feet (@24Vdc)
• For Fire Alarm applications, the Sounder Volume must be at the highest setting, (see volume control section). For fire alarm use, Tone
12 as shown below must be selected:
• Connection Terminals: Pluggable
AC: 1.0 - 2.5mm
2
/ AWG18 - AWG12
DC: 0.2 - 2.5mm
2
/ AWG24 - AWG12
•
Terminal Tightening torque 0.4Nm
•
To maintain Ingress Protection, cable entries must be fitted with suitably rated cable glands or stopping plugs
•
Units can be located indoor or outdoor wet use, wall or ceiling mounted and there are no limitations on orientation
•
Factory finishes are not intended to be modified
Attention: Installation must be carried out by an electrician in compliance with the National Electrical Code, NFPA 70, and the National Fire Alarm
Signaling Code, NFPA 72 or CSA 22.1 Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32. / L'installation doit
exclusivement être réalisée par du personnel qualifié, conformément au code national d'électricité américain, NFPA 70, et le code national d
’ alarrme
incendie et de signalisation NFPA 72 ou CSA 22.1 Code canadien de l'électricité, première partie, norme de sécurité relative aux installations électriques,
Section 32
Attention: Disconnect from power source before installation or service to prevent electric shock / Débranchez - le de la source d'alimentation avant l'instal-
lation ou l'entretien pour éviter tout choc électrique.
Attention: Do not paint / Ne pas Peinturer
1000Hz(0.5s on, 0.5s off)x3 + 1s gap ISO 8201 Temporal
Pattern
Stage 1
Set DIP
SW 1
Tone No.
Tone Description Tone Visual
Stage 1 & 2
DIP SW 1/2
Settings
1 2 3 4 5 6
Stage 3
Set DIP
SW 1
(S3)
Stage 4
Set DIP
SW 1
(S2 + S3)
12 1 1 0 1 0 0
1000Hz 0.5s
0.5s
0.5s
0.5s
0.5s
1s
1 8
Surge Current Ratings for use in fire alarm systems
Model Nominal Voltage Voltage Range Initial Peak Initial RMS
D1xS1 - DC024 - A
24V dc
11.5 - 54V dc P1: 1312mA P1: 159mA
D1xS1 - DC024 - S P1: 1312mA P1: 159mA 20 - 28V dc
D1xS2 - DC024 - A P2: 1005mA / P3: 1267mA P2: 286mA / P3: 553mA 11.5 - 54V dc
D1xS2 - DC024 - S 20 - 28V dc P2: 1005mA / P3: 1267mA P2: 286mA / P3: 553mA