E-data DSL-2120 Series User Manual Download Page 7

Page: 7 / 86

Proprietary & Confidential

Page

7 of 86

Revision: V1.0

Apr. 23, 2008

You must register for this service with a Dynamic DNS client.

Multiple PVC (Permanent Virtual Circuit) Support

Your DSL-2120/2120W supports up to 8 PVCs.

ADSL Standards

♦

Compliant to ITU-T G.992.1 (G.dmt), G.992.3 (ADSL2), G.992.4, and G.992.5

(ADSL2+) Annex A, B, I, J, L, and M

♦

Supports Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.994.1

and G.996.1 (for ISDN only); G.991.1; G.lite (G992.2))

♦

Supports OAM F4/F5 loop-back, AIS and RDI OAM cells

♦

ATM Forum UNI 3.1/4.0 PVC

♦

Supports up to 8 PVCs (UBR, CBR, VBR)

♦

Multiple Protocols over AAL5 (RFC 1483)

♦

PPP over AAL5 (RFC 2364)

♦

PPP over Ethernet (RFC 2516)

DHCP Support

Dynamic Host Configuration Protocol (DHCP) allows individual clients (computers) to get

TCP/IP configuration information at start-up from a DHCP server. The DSL-2120/2120W has

its built-in DHCP server capability enabled by default. It can assign IP addresses, an IP default

gateway and DNS servers to DHCP clients. The DSL-2120/2120W can also act as a substitute

DHCP server (DHCP Relay), relaying IP address assignment from the actual DHCP server to

the clients.

IP Alias

IP Alias allows you to partition a physical network into logical networks over the same

Ethernet interface. The DSL-2120/2120W can support up to 3 logical LAN interfaces through

its physical Ethernet interface with the DSL-2120/2120W acting as the gateway for each

network.

IP Policy Routing (IPPR)

Normally, routing is based only on the destination address; the router forwards the packet

along the shortest path. IP Policy Routing (IPPR) is a method to override this routing behavior

and change the forwarding path based on policies defined by the network administrator.

Protocol Support

♦

Point-to-Point

Protocol

(PPP) link layer protocol

PPP over PAP (RFC 1334)

PPP over CHAP (RFC 1994)

♦

RIP I/RIP II

♦

IGMP

Proxy

♦

ICMP

support

♦

MIB II support (RFC 1213)

Summary of Contents for DSL-2120 Series























































































Search results

Summary of Contents for DSL-2120 Series

Reviews:

Related manuals for DSL-2120 Series

Brands by name

Popular brands

E-data DSL-2120 Series, User Manual

Search results

Summary of Contents for DSL-2120 Series

Reviews:

Related manuals for DSL-2120 Series

Brands by name

Popular brands