Dynisco ViscoIndicator Installation & Service Manual Download Page 45

Page: 45 / 50

P/N: 975389

Rev: current

ECO: xxxxx

www.dynisco.com

From lab to production,

providing a window into the process

-45-

Preventative Maintenance

8.1

Check RSU enclosure for plastic leaks

•

Remove the 6 screws holding on the right cover of the RSU (yellow circles) This is

the cover on the right hand side of the RSU if the RSU is between yourself and the

extruder.

•

Caution: RSU should be properly supported before removing 2 mounting screws

holding head onto bracket.

•

Visually examine all the pressure port connections to the flow block/flange

(pressure transducer, burst plug, and capillary plate)

•

If extrudate is seen, retighten connections at leak points at check system

•

Reinstall the cover.

Summary of Contents for ViscoIndicator



















































Search results

Summary of Contents for ViscoIndicator

Reviews:

Related manuals for ViscoIndicator

Brands by name

Popular brands

Dynisco ViscoIndicator, Installation & Service Manual

Search results

Summary of Contents for ViscoIndicator

Reviews:

Related manuals for ViscoIndicator

Brands by name

Popular brands