background image

From lab to production, 

providing a window into the process 

-15-

www.dynisco.com

Rev: 1117

P/N: n/a

ECO: n/a

Toxic hazard!

The PT contains a very small amount of mercury (Hg) as its 

transmission medium. If the diaphragm is damaged, mercury

may escape. Non-toxic NaK is being used in the LDA series. NaK is 

also available as an option for other pressure transducers. Never 

transport or store the PT without the protective shell bolted in 

place. Remove the shell shortly before installation.

If mercury is inhaled or swallowed, seek medical attention 

immediately.

Mercury is hazardous waste and must be disposed of in 

accordance with applicable laws. 

DYNISCO

 will accept defective 

PTs.

If mercury escapes, use airtight packaging!

Alternative, non-toxic transmission media (Oil or NaK) available 

on request.

ESD sensitive component. Electrostatic discharge may damage 

the PT. Take ESD precautions.

5.1 Transport/packing/transport damage

- Do not let the PT be damaged by other items during transit.

- Use only the original packaging.

- Report transport damage to 

DYNISCO

 immediately in writing.

5.2 Storage

- Store the PT in original packaging only.

- Protect against dust and moisture.

5.3 Scope of delivery

- PT with diaphragm protection cap

- Cable socket

- Fastening clip (transmitter with flexible stem only)

- Calibration sheet

- Operating manual

Summary of Contents for LDA 415
































Reviews: