manualshive.com logo in svg

Dynamix ITM Series, Installation, Operation & Maintenance Manual, Page: 14 / 23

Share
Download
Dynamix ITM Series Installation, Operation & Maintenance Manual Download Page 14

R16 122016

 

 

 

14 

Air Motor Rebuilds 

 
Note:

  Air  motor  rebuilds  are  often  not  worth  the  parts  and  labor  costs  considering  with  the  resulting  performance  vs. 

purchasing a new air motor

.  

 
Please email or call to request current procedure from Dynamix Agitators Inc.  
[email protected] - (604) 244 3771 

 

Air Motor 1.5HP Rating 

 

 

 

 

 

 
Exploded  views  are  shown  for  reference  only.  Units  may  vary  depending  upon  specific  model.  Please  refer  to  factory  if 
you are unsure of your model.  
 
 

∆ Denotes parts included in the Service Kit: 

 

REF# 

DESCRIPTION 

QTY 

1 

∆ 

Shaft Seal 

1 

2 

∆ 

Drive End Bearing 

2 

3 

Drive End Plate 

1 

4  

Rotor Assembly 

1 

5 

∆ 

Vane 

4 

6 

∆ 

Push Pins 

4 

7 

∆ 

Vane Springs 

2 

 

REF#

 

DESCRIPTION

 

QTY

 

8  

Body 

1 

9 

∆ 

Shims 

2 

10  

Dead End Pla e 

1 

11 

∆ 

End Cap Gasket 

1 

12  

Dead End Cap 

1 

13  

Muffler Assembly 

1 

 

 

 

Summary of Contents for ITM Series
























Reviews:

No comments