manualshive.com logo in svg

Dynamix ITM Series, Installation, Operation & Maintenance Manual, Page: 1 / 23

Share
Download
Dynamix ITM Series Installation, Operation & Maintenance Manual Download Page 1

R16 122016

 

 

 

1 

 

 

 

 

    

  

Installation, Operation & Maintenance Manual 

 

 

 
 
  

ITM Series

 

   

INTEGRATED TOTE MIXER

 

 

 

Important Safety Instructions 

 
This Installation and Operation Manual Includes  

Important Warnings and Safety Information. 

 
Be sure to keep this manual with equipment and  
ensure 

all operators

 read the enclosed information.

 

 
 

Table of Contents 

 

Important Safety Warnings.............................. 2 

Receiving, Inspection & Storage ..................... 3 

Operation Instructions ..................................... 4 

Startup Checklist ............................................. 5 

Assembly & Installation 

Plastic Tote ......................................... 6 

Stainless Steel Tote ............................  7 

Parts, Maintenance & Service 

Plastic Tote ......................................... 8 

Stainless Steel Tote ............................ 9 

Terms & Conditions ........................................ 16 

Warranty ......................................................... 17 

 

 

 

ITM SERIES 

Integrated Tote Mixer

 

 
 
     

Dynamix Agitators Inc. 

 

 
      150 - 14480 River Road,  
      Richmond, B.C, Canada V6V 1L4 
      Ph. 604.244.3771   Fax 604.244.3772 
 
      

info@dynamixinc.com

 

      

www.dynamixinc.com

 

Summary of Contents for ITM Series
























Reviews:

No comments