manualshive.com logo in svg

Dynamica HALO DNAmaster, Operation Manual, Page: 9 / 44

Share
Download
Dynamica HALO DNAmaster Operation Manual Download Page 9

 

SAFETY-

3

 

 

 

 SAFETY SUMMARY (Continued)

 

 
 
 

General Safety Guidelines (Continued) 

 
 

Before Using

 

 

 

Before using this product, please make sure you read and understand the instructions. 

 

 

Please keep this manual in a safe and easily accessible place so that you can use it when 
necessary. 

 

 

Please make sure to use this product properly and follow the instructions as specified in this 
manual.

 

 

 

Please make sure to understand and follow the instructions regarding safety in this manual.

 

 

 

If you do not follow the instructions in this manual, an inaccurate analysis may result or 
bodily injury may occur. 

 

 

Because of danger, please make sure not to modify or alter the product, make sure not to 
use unspecified parts, and make sure not to operate the equipment by removing/defeating 
the safety device(s). 

 

 

When using chemicals, please make sure to ventilate the room well.    If there is not enough 
ventilation, it may be hazardous to your health. 

 

 

Although we have carefully considered the instructions written on the products and 
manuals, it is possible for an unexpected event to occur.    When operating the equipment, 
aside from following the instructions, be very cautious.   

 
 

 

 
 
 

Summary of Contents for HALO DNAmaster













































Reviews:

No comments