Dynamica HALO DNAmaster Operation Manual Download Page 10 | Manualshive

Page: 10 / 44

Dynamica HALO DNAmaster Operation Manual Download Page 10

SAFETY-

4

SAFETY SUMMARY (Continued)

General Safety Guidelines (Continued)

Precautions for Installation • Maintenance • Relocation and After Sale Technical
Service

Before installation, confirm that there are no missing items or standard

accessories. If there is something missing or damaged, or you have noticed any

problems, please contact our nearest representative.

Operating the equipment without a standard part can damage the equipment

and cause safety concerns. If that occurs, please follow the instruction of the

installer.

Installation of this instrument shall be carried out by or under supervisions of

qualified service personnel of Dynamica or its authorized service agent.

When relocation of this instrument becomes necessary after initial installation

(delivery), please notify your local Dynamica sales representative or nearest

Dynamica service office. Technical support service for this instrument is available

from s service agent approved or authorized by Dynamica within regular working

hours or workdays.

Please do not perform any other operations that are not included in the manual.

If any problem occurs with the equipment, please contact the agent from whom

you purchased it or the service department of Dynamica.

«
...
8
9
10
11
12
...
»

Summary of Contents for HALO DNAmaster













































Reviews:

No comments