background image

16

•  Do not charge the battery on a surface (such as a kitchen counter top) which 

could be damaged by the acid contained inside the battery. Take precautions to 
protect the surface on which you charge your battery.

•  Use only an original charger (AC 120V 60Hz) with an output of DC 24V (1A) to 

charge your ride-on toy battery.

• 

NOTE TO ADULTS:

 Regularly examine the charger for damage to the cord, plug, 

housing or other parts that may result in the risk of fire, electric shock or injury.

•  If your battery is old and will not accept a charge, do not leave it in the ride-on toy. 

Always remove a dead battery from the ride-on toy.

•  After the first charge, recharge the battery for at least 12 hours after each use. 

Never charge the battery longer than 30 hours. Charge the battery after each use, 
regardless of how long the ride-on toy was used.

•  Do not allow the battery to run down completely before charging.
•  Charge the battery before storing the ride-on toy.
•  Charge the battery at least once per month, even if the ride-on toy has not been used.

NOTE:

•  This product has CHARGING PROTECTION: when charging, all the functions will 

be cut off.

•  Recharges after initial charge - At least 12 hours, and never charge the battery 

longer than 30 hours.

•  When the ride-on toy begins to run slowly, recharge the battery. 
•  After each use, or at least once per month when not in use, recharge the battery 

for at least 12 hours and less than 30 hours at most.

 WARNING:

 Use the charger in dry locations only.

1. Plug the charger port into the input socket (the socket is under the seat).
2. Plug the charger plug into a wall outlet. The battery will begin charging.

NOTE:

 

Red LED light indicates battery is charging and a green LED light indicates 

battery is nearly fully charged. (If the lights on the charger do not light up, check the 
power to the outlets.) If you have any charging questions or issues, please make 
sure that you have charged your unit according to the recommended charging times 
outlined in this manual, i.e., at least 18 hours before first use and at least 12 hours  
after each subsequent use, before contacting our Customer Service Team.

Charging Input 

Socket

1

2

Summary of Contents for 24V TRAIL RACER

































Reviews: