DXV Rem D35100330 Installation Instructions Manual Download Page 1

Page: 1 / 8

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017

VE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.

M965497 Rev. 1.6 (5/17)

Model D35100330

Rem

3-Hole Bidet Set

with Vacuum Breaker

Plumbers' Putty or Caulking

Adjustable Wrench

Phillips Screwdriver

Channel Locks

Tubing Cutter

Flat Blade Screwdriver

Basin Wrench

ROUGHING-IN DIMENSIONS:

• For reference

DIVERTER

AND VACUUM

BREAKER

1-1/2"

(38 mm)

LIFT ROD

5-5/8"

(143 mm)

2-7/16"

(62 mm) D.

2-1/2" to 6"

(64 to 152 mm)

2-1/2" to 6"

(64 to 152 mm)

(51 mm)

1-1/8" D.

(29 mm)

1-1/8" D.

(29 mm)

7" MAX

(178 mm)

2" MAX

(51 mm)

2-1/8" DIA.

(54 mm)

1-1/4" O.D.

(32 mm)

13" MAX

(330 mm)

4" MAX

(102 mm)

SPRAY

CONNECTIONS ARE FOR 1/2" IPS

FLEXIBLE SUPPLIES or 3/8" O.D.

BULL-NOSE RISERS

(75 mm)

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

Summary of Contents for Rem D35100330









Search results

Summary of Contents for Rem D35100330

Reviews:

Related manuals for Rem D35100330

Brands by name

Popular brands

DXV Rem D35100330, Installation Instructions Manual

Search results

Summary of Contents for Rem D35100330

Reviews:

Related manuals for Rem D35100330

Brands by name

Popular brands