10
English
Symbol
Meaning
Useful information.
Do not dispose of the power
tool in a domestic waste
container.
DWT
power tool designation
The power tool is designed for cutting of stone
facework, marble and ceramic tiles.
The power tool is designed for right-handed users
only.
1
Power tool
components
Body
2
Base plate
3
Ventilation slots
4
On / off switch
5
Lock-on button
6
Guide
7
External flange
8
Cutting disc fixing bolt
9
Guard cover
10
Clamping plate
11
Wing screw
12
Cutting disc *
13
Vacuum cleaner adapter *
14
Dust removing coupler *
15
Screw *
16
Socket wrench *
17
Flange wrench *
18
Spindle
19
Internal flange
20
Fastening screw of guide
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / replacement of cutting disc (see fig. 1-4)
After mounting of cutting disc, make a
trial run before commencing operation -
start the power tool and let it work in idle
mode for not less than 30 seconds. The
operation of cutting disc with radial or axial run-
out and causing increased vibration of the power
tool is strictly forbidden.
After prolonged operation, the cutting
disc can become very hot, remove it
using gloves. This will also reduce the
risk of injury by the cutting edge.
•
Mount power tool on the side end of the motor as
shown in fig. 1.
• Holding the external flange
7
by means of the
flange wrench
17
, unscrew the bolt
8
by the socket
wrench
16
. Remove the bolt
8
.
Attention: the bolt 8
has left hand threading.
• Remove from the spindle
18
: the external flange
7
,
the cutting disc
12
, the internal flange
19
(see fig. 2).
•
Clean fastening elements with the help of a soft brush
and mount to the spindle
18
: the internal flange
19
, the
cutting disc
12
, the external flange
7
. Screw bolt
8
by
hand into the threaded hole of the spindle
18
.
Attention! observe the following rules during
installation:
• follow the mounting sequence (see fig. 3); avoid
bending during mounting;
•
while installing the cutting disc
12
make sure that
the diameter of the bore hole of the disc corresponds
with diameter of the locating tab of the internal
flange
19
;
•
direction of the indicator at the cutting disc
12
must always coincide with a direction of the indicator
at the guard cover
9
.
• Holding the external flange
7
by means of the flange
wrench
17
screw the bolt
8
by socket wrench
16
(see
fig. 4).
Mounting / dismounting the dust extractor system
(see fig. 5)
•
Join coupler
14
and adapter
13
, as shown in
figure 5.
•
Loosen the fastening screw
20
and lift the power tool
frame to the upper position.
•
Mount the coupler
14
(connected with adapter
13
)
and lock it with the screw
15
, as shown in figure 5.
• Disassembly operations do in reverse sequence.
Initial operating
of the power tool
Always use the correct supply voltage: the power
supply voltage must match the information quoted on
the power tool identification plate.
Switching the power
tool on / off
Short-term switching on / off
To switch on, press and hold on / off switch
4
, to switch
off - release it.
Long-term switching on / off
Switching on:
Push on / off switch
4
and lock it in the position with
lock-on button
5
.
Switching off:
Push and release on / off switch
4
.
