DUROMAX XP5500HX User Manual Download Page 48

Page: 48 / 82

USING THE GENERATOR (CONTINUED)

Connecting a load to the generator

NOTE: Be sure to attach devices to the correct receptacle (outlet).

●

120v devices can be directly connected to the 120v ONLY receptacles.

●

120v devices can be connected to the 120/240v receptacle using an appropriate adapter.

●

240v devices can ONLY be connected to the 240v receptacle.

Plug in devices

Turn breaker on

Turn on connected devices

Plug in devices to the appropriate receptacle. When using

the generator balance the load as closely as possible. Placing

more load on one side of the circuit will reduce the breaker

trip period.

Flip the circuit breaker up to the on position to allow power to

the receptacles.

Start or turn on appliances starting with the biggest loads

first.

CAUTION

: Do not connect 50Hz or 3-phase loads to the generator.

Summary of Contents for XP5500HX



















































































Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands

DUROMAX XP5500HX, User Manual

Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands