DUROMAX XP5500HX User Manual Download

Page: 28 / 82

Step 3 - Connect the Battery

GENERATOR SETUP (CONTINUED)

Disconnected on arrival

Cover the terminal

Cover the connected terminal with the black rubber

boot.

Locate the negative cable

Locate the negative battery cable above and behind

the battery. One side is connected to ground and

the other end needs to be connected to the battery.

Route the free end to the negative battery terminal.

Connect the negative cable

Push the black rubber boot up the wire to expose

the connector.
b.

Securely connect the free end of the battery cable

to the negative battery terminal using the screw

and nut from the battery with the screwdriver and

wrench from the toolkit.

The generator battery is disconnected on arrival to prevent

discharge or accidental starting in storage and transportation.

Summary of Contents for XP5500HX



















































































Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands

DUROMAX XP5500HX, User Manual

Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands