DUROMAX XP5500HX User Manual Download

Page: 35 / 82

Check fuel level

If running the engine on gasoline check to see that there is

sufficient gasoline in the fuel tank. The fuel gauge on top of

the tank will give a rough estimate of the gasoline level. The

gauge will appear white then fill red as the tank is filled.

Note: Fuel gauge may not register with less than 1/3

fuel tank full.

Step 2 - Check the gas level (Optional)

DANGER

DO NOT OVERFILL

THE GAS TANK

OVERFILLING CAN RESULT

IN A FIRE, EXPLOSION,

OR DEATH.

1.5”

WARNING

: Gasoline and gasoline fumes are highly flammable.

●

Do not fill the tank near an open flame.

●

Always allow the engine to cool for several minutes before refueling.

●

DO NOT overfill the fuel tank. Fuel expands when shaken or heated. ALWAY leave 1

“

space or more at the top of the tank.

●

ALWAYS use fresh fuel or stabilized fuel. Old gasoline (older than 30 days) can cause
permanent damage to the fuel system.

●

Always check for fuel spills.

Summary of Contents for XP5500HX



















































































Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands

DUROMAX XP5500HX, User Manual

Search results

Summary of Contents for XP5500HX

Reviews:

Related manuals for XP5500HX

Brands by name

Popular brands