DUROMAX XP18HPX User Manual Download Page 25 | Manualshive

Page: 25 / 70

background image

CAUTION

: LPG must be shut off when using gasoline!

WARNING

:

Operating the starter motor for more than 5 seconds can damage the

motor. If the engine fails to start, release the switch and wait 10 seconds before

operating the starter again.

25

Move the choke lever to RUN

After allowing the engine to preheat, move the choke lever
to the right-hand side to the RUN position to steady the
idle speed and run the engine.

5.

Adjust the throttle lever

Adjust the throttle lever to the proper position for the
desired speed and the engine is ready for use.

6.

«
...
23
24
25
26
27
...
»

Summary of Contents for XP18HPX







































































Reviews:

No comments

Related manuals for XP18HPX

Brand: Eurotronic Pages: 4

Brand: Turnigy Pages: 2

Brand: Yamaha Pages: 30

Brand: Cobra Pages: 15

Brand: Grizzly Pages: 2

Brand: Lycoming Pages: 568

SKALAR SC Series

Brand: Hacker Pages: 2

Brand: RAAMDECORATIE Pages: 45

Brand: Greyhound Pages: 19

Brand: Yanmar Pages: 214

Brand: Kingfisher Pages: 10

Brand: MULTIPLEX modell Pages: 6

Brand: Honda Pages: 15

Brand: Honda Pages: 60

Brand: O.S. engine Pages: 30

Brand: Honda Pages: 64

Brand: Honda Pages: 86

Brand: DLE Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands