Duratech megavoice 2000 Installation Manual Download Page 16

4. PROGRAMMING

4.1 GENERAL

Megavoice is controlled with DTMF codes. One command starts with   and ends with #. 
Different fiels are separated by   except 1st one  which is line number. If value field is  , 
Megavoice displays the value.   can have also other meanings like all lines  like  1

#. 

Eg. Play back message 1 is    3 1 #. 

Megavoice replays with 2 beeps=OK-tone, or with 9-beeps=Error-tone, or 1beep= wait/ 
information tone.Eg. Device gives information tone before and after playing one 
message with play command. Then the lenght of the message can be timed exactly. 

LCD display indicates error and Ok and many useful information, like free memory, 
parameter values,  or how many calls per line. The maintenance and learnig is easier 
with display. If remote programming is used, the first command is login and the last is 
logout. Megavoice logouts if no command are used for 3 minutes.

The set up data must be stores with  66 # into non-volatile memory for power failures at 
the end of installation. Line counters are backed up every 24h. Remote mode changes 
are immediately stored.

Megavoice has 1 lines. They have 4 modes : Day/night/vacation/programming. There 
are 9 possible messages. During installation the functioning of the line must be 
programmed; direct/delayed answer AND information or tnumber.  
Also the message given in different line/mode states must be entered. Default values 
can be used, which saves some work.

4.2 FRONT PANEL SWITCHES

The front panel switches are not usually used,
but can be used in special cases.

Switch 5 : If down(1) and Megavoice is power up, the factory set up values are used and 
                 they can be stored.

Switch 6: If down(1), Megavoice do not wait extra 1s between commands to indicate 
                value in the LCD.
 
Switch 7: If down(1), the programming mode is not timed and there is no automatic 
               release. Also if  594=3 and sw7=1 (on), L1 is  in the programming state
               immediately. The programming can be done with CD player script on L1.

Switch 8 : If down (1), All passwords are accepted as  0 # command. Also must be 

      down if message 9 or all messages are erased.

V

V

V

V

V V V 

V

12

OFF

ON

1 2  3   4  5  6  7   8

0

1

1          SW        8

12

MEGAVOICE 2000 V.3.1 MANUAL V.2000-09-20

Summary of Contents for megavoice 2000



























Reviews: