background image

 

 

180 DS 

 

duralloy.net.au 

 

 

7. Operation Notices 

7.1 Installation 

(1)Welding environmental temperature should be between -10

 to 40

(2)Welding  should  be  done  in  relatively  dry  environments,  with  air  humidity  of  not 
more than 90%. 
(3) Avoid areas containing dust or corrosive gas whilst welding. 
(4) Avoid sunlight or rain, do not let water or rain infiltrate the welding machine. 

 

7.2 Safety 

When  the  Welding  machine  has  encountered  over-voltage,  over  current  and  over 
temperature protection circuit, when the primary voltage, output current and the internal 
temperature exceeds the set temperature, the welding machine will automatically stop 
working; so you need to note the following: 

 

(1)  To ensure good ventilation! 
The machine is equipped with internal cooling fan ensure that there is adequate air flow 
around the machine. 
   
(2) Do not exceed duty Cycle! 
Operators  should  ensure  to  use  the  machine  within  its  normal  range  of  operation, 
continually putting the machine in overload will reduce life of the equipment in the longer 
term.   
 
(3) Ensure machine is connected to correct voltage! 
The machine should only be connected to 15Amp 240v Power supply 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for 180DS












Reviews: