Duplo DF-1200 Instruction Manual Download Page 87

Page: 87 / 98

5-5

Chapter 5 Trouble Guide

2-2. Folding plate

Holding on the cancel key, press the

clear key.

Eject forcibly the paper inside the folding

plate.
Forcible ejection in the folding plate will not

stop until the folding stopper returns to the

home position, as the folding stopper moves,

even if the key is not held.

Even if the paper is not removed after forcible ejection, check the position of paper jam to remove the paper

with the following method.

Folding plate 1

Take out the folding plate 1.

Attach the folding plate 1 holding with

both hands.

Open the top cover.

Open or close the top cover

gently.

Hands or fingers may be caught in the

cover section. Doing so may result in

injury.

Pull out the paper rotating the jam

correction knob.

Close the top cover.

Summary of Contents for DF-1200



































































































Search results

Summary of Contents for DF-1200

Reviews:

Related manuals for DF-1200

Brands by name

Popular brands

Duplo DF-1200, Instruction Manual

Search results

Summary of Contents for DF-1200

Reviews:

Related manuals for DF-1200

Brands by name

Popular brands