DTSL3/FR MKII USER’S MANUAL
13
Chapter
Chapter
Chapter
Chapter 4
4
4
4 INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION
SKILLED
SKILLED
SKILLED
SKILLED AND
AND
AND
AND AUTHORISED
AUTHORISED
AUTHORISED
AUTHORISED PERSONNEL
PERSONNEL
PERSONNEL
PERSONNEL ONLY
ONLY
ONLY
ONLY SHOULD
SHOULD
SHOULD
SHOULD BE
BE
BE
BE ALLOWED
ALLOWED
ALLOWED
ALLOWED TO
TO
TO
TO PERFORM
PERFORM
PERFORM
PERFORM THESE
THESE
THESE
THESE OPERATIONS,
OPERATIONS,
OPERATIONS,
OPERATIONS,
FOLLOW
FOLLOW
FOLLOW
FOLLOW ALL
ALL
ALL
ALL INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS SHOWN
SHOWN
SHOWN
SHOWN BELOW
BELOW
BELOW
BELOW CAREFULLY,
CAREFULLY,
CAREFULLY,
CAREFULLY, IN
IN
IN
IN ORDER
ORDER
ORDER
ORDER TO
TO
TO
TO PREVENT
PREVENT
PREVENT
PREVENT POSSIBLE
POSSIBLE
POSSIBLE
POSSIBLE DAMAGE
DAMAGE
DAMAGE
DAMAGE TO
TO
TO
TO
THE
THE
THE
THE CAR
CAR
CAR
CAR LIFT
LIFT
LIFT
LIFT OR
OR
OR
OR RISK
RISK
RISK
RISK OF
OF
OF
OF INJURY
INJURY
INJURY
INJURY TO
TO
TO
TO PEOPLE.
PEOPLE.
PEOPLE.
PEOPLE.
Skilled technicians only appointed by the same manufacturer or by authorised dealers, are allowed to install the car lift.
INSTALLATION REQUIREMENTS
�
The car lift must be installed according to the specified safety distances from walls, pole and what other equipments stated.
(Picture 12)
�
The specified safety distances from walls must be 1000 mm at least, taking into consideration the necessary space to work
easily. Because space for the control site and for possible runways in case of emergency is also necessary.
�
The room must be previously arranged for the power supply and pneumatic feed of the car lift.
�
The room must be 4000 mm in height, at least.
�
The car lift can be placed on any floor, as long as it is perfectly level and sufficiently resistant. (≥250 kg/ cm², the thickness of
concrete ≥ 150 mm)
All parts of the machine must be uniformly lit with sufficient light to make sure that the adjustment and maintenance operations can
be performed safely, and without reflected light, glare that could give rise to eye fatigue.
�
The integrality of arrived goods should be checked before the lift is installed.
�
Moving and installing lift should follow the process as the picture instructs.
The
The
The
The transport
transport
transport
transport and
and
and
and storage
storage
storage
storage of
of
of
of machine
machine
machine
machine refers
refers
refers
refers to
to
to
to “
“
“
“TRANSPORT
TRANSPORT
TRANSPORT
TRANSPORT AND
AND
AND
AND STORAGE
STORAGE
STORAGE
STORAGE”
”
”
” on
on
on
on page
page
page
page 4.
4.
4.
4.
Platform
Platform
Platform
Platform Installation:
Installation:
Installation:
Installation:
-Place two platforms on the position of the location.
-The bottom of oil cylinder is located in the frontage of machine (the direction of getting on the vehicle)
-Use fork car or other lifting equipments to lift the platform (Picture 13) and make sure that the safety equipment of machine is both
turned on and locked.
To avoid failure of machine safety equipment, can insert a wood in the middle part of joint-pole.
Prohibit working beneath the lift when hydraulic system is not completely equipped with hydraulic oil and take the action of up and
down operations.
-When moving the lift platform, adjust the space between two platforms; make sure that the two platforms are parallel.
LINE
LINE
LINE
LINE CONNECTION
CONNECTION
CONNECTION
CONNECTION
Connect the electrical and oil line according to ‘the electrical diagram’ and ‘oil pipe connection diagram’.
In the process of connecting oil pipes, pay particularly attention to the protection of pipe tie-in to prevent abnormal thing from
entering oil loop, then damaging hydraulic system.
Picture 13
Picture 12