Dunkirk 90-100 Installation, Operation & Maintenance Manual Download Page 8

8

Complete all of the following prior to installing the boiler.

Codes

This boiler product is a gas-fired, direct vent, condensing boiler and 

must be installed to conform to the requirements of the authority 

having jursidiction or, in the absence of such requirements:
United States - National Fuel Gas Code (NFPA-54/ANSI Z223.1).
Canada - National Gas and Propane Installation Code, Can/CSA 

B149.1.

Where required by the authority having jurisdiction, the installation 

must conform to the American Society of Mechanical Engineers 

Safety Code for Controls and Safety Devices for Automatically Fired 

Boilers, No.CSD-1.

NOTICE

Important - In the state of Massachusetts 

this product must be installed by a licensed 

plumber or gas fitter and the installation must 

be in accordance with 248 cMR

.

Installers

 - Follow local regulations with respect to installation of 

CO (Carbon Monoxide) Detectors. Follow maintenance recommen-

dations in this manual.

Installation Requirements Specific To The State Of 

Massachusetts For Direct Vent, Mechanical Vent, And 

Domestic Hot Water Appliances

For all side wall horizontally vented gas fueled equipment installed 

in every dwelling, building or structure used in whole or in part 

for residential purposes, including those owned or operated by the 

commonwealth and where the side wall exhaust vent termination is 

less than seven (7) feet above finished grade in the area of the vent-

ing, including but not limited to decks and porches, the following 

requirements shall be satisfied:

Installation of carbon monoxide detectors: at the time of instal-

1. 

lation of the side wall horizontal vented gas fueled equipment, 

the installing plumber or gasfitter shall observe that a hard 

wired carbon monoxide detector with an alarm and battery 

back-up is installed on the floor level where the gas equipment 

is to be installed. In addition, the installing plumber or gasfitter 

shall observe that a battery operated or hard wired carbon mon-

oxide detector with an alarm is installed on each additional level 

of the dwelling, building or structure served by the side wall 

horizontal vented gas fueled equipment. It shall be the respon-

sibility of the property owner to secure the services of qualified 

licensed professionals for the installation of hard wired carbon 

monoxide detectors.

Read the entire installation manual before beginning the instal-

1. 

lation. Failure to follow these rules for safe installation and 

operation and these instructions could cause a malfunction 

of the boiler and result in death, serious bodily injury, and/or 

property damage.
Check all applicable state and local building codes and util-

2. 

ity company requirements before installation. The installation 

must conform with these requirements in their entirety. In the 

absence of these codes, use NFPA Installation Codes and good 

industry practice.
Before servicing the boiler - allow the boiler to cool. Always 

3. 

shut off any electricity and gas supply connected to the boiler 

prior to servicing.
Inspect gas line for leaks.

4. 

Be certain gas input rate is correct. Over firing may result in 

5. 

early failure of the boiler sections. This may cause dangerous 

operation. Under firing may result in too much air for the pre-

mix burner causing poor or loss of combustion.
Never vent the products of combustion from this boiler to an 

6. 

enclosed space. Always vent to the outdoors. Never vent to 

another room or to inside a building.
Be sure there is adequate outdoor air supply to boiler for com-

7. 

plete combustion.

Follow a regular service and maintenance schedule for efficient 

8. 

and safe operation. 
Keep boiler area clean of debris and free of combustible and 

9. 

flammable materials.
Proper through the wall or through the roof combustion vent-

10. 

ing shall be in accordance with the materials and methods 

described in this manual. Installation must comply with local 

codes.
This boiler and related hot water heating systems are not do it 

11. 

yourself items. They must be installed and serviced by qualified 

professionals.

rules for safe insTallaTion and operaTion

before insTalling THe boiler

!

  

WARNING

This boiler has been equipped for residential 

installations. If used for commercial 

applications, any additional code requirements 

must be adhered to for installation. This may 

require additional controls including but not 

limited to a low water cut off, a manual reset 

high temperature limit, and wiring and/or 

piping modifications. The manufacturer is not 

responsible for any field installation changes 

made to a boiler installation which are not 

described or acknowledged in this manual.

Summary of Contents for 90-100

























































Reviews: