background image

Page iii

Name: 

Michael Ricks

Title:

   General Manager

x

Place and Date

Fremont, CA on 02 July 2020

Remark:

 This Declaration of Conformity replaces all previous ones for the above products.

ETL Certified and Listed

The named products conform or are certified to the following standards relating to 

the safety of electrical equipment for measurement, control, and laboratory use:

UL:

  

61010-1:2012 Ed.3+R:29APR2016

CSA:

  

C22.2#61010-1-12:2012 Ed.3+U1;U2;A1

Declaration of Conformity

2003309

EMC:

  

EN 61000-6-1:2019

   

EN 61000-6-3:2007+A1:2011

   

EN 61326-1:2012RLV

LVD:

  

EN 61010-1:2010+A1:2019

Product Name:

  

Terranova® 751A Medium Ion Pump Power Supply

 

 

 

Terranova® 752A Dual Ion Pump Power Supply

The named products are in conformity with the following requirements of the EU directives:

Electromagnetic Compatibility Directive (2014/30/EU)
Low Voltage Directive (2014/35/EU)

We declare, under  our  sole  responsibility, that the named  products  which  display the 

CE  mark  are  in  conformity  with  the  following  harmonized  standards  and/or  normal 

documents or technical specifications:

Manufacturer:

  

Duniway Stockroom Corp.

 

 

 

48501 Milmont Drive

 

 

 

Fremont, CA 94538 

Summary of Contents for T-752A-F110




























































Reviews: