manualshive.com logo in svg

Dumor 331, Operation Manual

Share
Download
Dumor 331 Operation Manual Download Page 2

 

                                                                              331 Auto Creaser                                                                    2 

INDEX 

Chapter 1 INTRODUCTION ............................................................................. 1

 

1.1 Preface ............................................................................................... 1

 

1.2 Specification ....................................................................................... 2

 

Chapter 2 SAFETY .......................................................................................... 3

 

2.1 Environment ........................................................................................ 4

 

2.2 Do’s and Don’ts .................................................................................. 4

 

2.3 Cautions.............................................................................................. 5

 

Chapter 3 MAIN PARTS & ASSIES ................................................................. 6

 

Chapter 4 INSTALLATION ............................................................................... 7

 

4.1 Output tray, stops and guides ............................................................. 7

 

4.2 Feeding extension .............................................................................. 7

 

4.3 Power socket and switch .................................................................... 8

 

Chapter 5 OPERATION ................................................................................... 9

 

5.1 Key Panel Introduction ........................................................................ 9

 

5.2 Quick Start ........................................................................................ 10

 

5.3 Screen Introduction ........................................................................... 11

 

5.3.1 Welcome Screen .................................................................... 11

 

5.3.2 Ready Screen ......................................................................... 11

 

5.3.3 Crease Data Screen ............................................................... 12

 

5.3.4 Cover Hinge Screen ............................................................... 13

 

5.3.5 Progressive Screen ................................................................ 13

 

5.3.6 Save a Job .............................................................................. 15

 

5.3.7 Recall a Job ............................................................................ 16

 

5.3.8 Speed Screen ......................................................................... 16

 

5.3.9 Recalibration Screen .............................................................. 17

 

5.4 Hardware Setting .............................................................................. 17

 

5.4.1 Skew adjustment .................................................................... 17

 

5.4.2 Crease Depth ......................................................................... 18

 

5.4.3 Crease Bar Installation ........................................................... 19

 

5.4.3.1 Crease Die Installation ................................................. 19

 

5.4.3.2 Perforation Bar Installation ........................................... 19

 

Chapter 6 OPTIONAL PARTS ........................................................................ 20

 

6.1 Perforating Wheel Set ....................................................................... 20

 

Chapter 7 TROUBLE SHOOTING ................................................................. 23

 

7.1 Show warning C-1 ............................................................................ 23

 

7.2 Show warning C-2 ............................................................................ 24

 

7.3 Show warning C-3 ............................................................................ 25

 

7.4 Show Error E-1 ................................................................................. 26

 

Chapter 8 Maintenance .................................................................................. 27

 

8.1 User Maintenance ............................................................................. 27

 

8.2 Technician Maintenance ................................................................... 27

 

 

Summary of Contents for 331






























Reviews:

No comments

Brands by name

Popular brands

Load more brands