43
D U C A T I
R a d i o r o l l i n g c o d e d K E Y P A D T A S T Y 6 5 0 0 / S W 6 5 0 0
SW6500/TASTY 6500 outdoor use DUCATI RADIO ROLLING
CODED KEYPAD works on433,92MHz frequency
By digiting a 4 digit codes + ENTER the keypad will transmit a rolling
coded radio signal to command your door opener.
Fix the keypad on wall or pillar. It’ss recommended to place where it
can be protected from rain even if it’s suitable for outdoor use. It must
be installed at a maximal distance of 10m from the electronic board of
the opener. The keypad is supplied with a standard code =1111.
It is recommended to replace the standard code with a personal secret
4 digit code before to store the keypad it in the electronic board’s
memory. it is possible to memorize max. 10 different personal code.
The Keypad are 1 channels only. Any of the memorized personal
coded will all be used to tramnsitt on the same channel ( each single
channel keypad can command 1 opener only)
Warning : it is extremely important to write down each personal code.
because if it is forgotten the keypad could not be resetted and it will be
unusefull.
Warning : in case of digiting a faulty code for 3 times the kaypad will turn into in stand-by for 10 minutes . Durring this stand-by time it wont accept any further digiting. Wait 10 minutes befor to try again to insert the
correct code.
1) How to replace the standard code with a personalized 4 digit code ( first operation)
digit the standard code 1111 + 3 + the 4 digit of the choosen personal code + ENTER. The keypad will make a BEEP to confirm that standard code has been replaced. ATTENTION: it is extremely important to write
down thepersonal code. In case it is forgotten the keypad cannot not be resetted by the customer and it will be unusefull. If hthis occurs it must be shipped back to the manufacturer to be resetted. Costs will be at the
charge of user.
A) To memorize the Keypad code in the electronic panel of the opener:
The door must be closed and idle.
- Press button P1 on the electronic board. The red LED switches on.
- Release button P1 and immediately on the keyswitch positioned by the electonic board digit the 4 personal code + ENTER ( hold enter for about 1,5sec. at least) until the keypad confirms with a “beeep”. Hold the -
the red LED light on the electronic board will quickly blink to show the procedure has been completed.
Warning: The memory of the electronic board of your opener can store up to 10-20 codes depending on the model (check the capacity of your memory card). If you need a larger number of remote controls is available
an optional external receiver (RIXY6040 o RIXI 6043)
To operate your gate you must digit on your KEYPAD your personal code + ENTER ( hold enter for about 1,5sec. at least)
2) How to replace a persoanl code with a new personal code:
digit the personal code you wish to be re 4 + the four digits of the new personal code + ENTER.
The keypad will make a BEEP to confirm that the personal code has been replaced.
3) HOW to add a new 4 digit code (without delating the previousely setted 4 digit codes):
digit one of the previously setted 4 digit codes+ 3 + the new 4 digit code + ENTER The keypad will make a BEEP to confirm
4) How to delate a specic 4-digit code from the keypad
digit the code you want to 5 + ENTER, the LED on the keypad will start blinking, press again on ENTER ( within 1,5sec.) and hold pressed until the LED blinks, then release Enter The keypad will make a BEEP
to confirm
5) How to delate all the codes setted in the keypad ( all codes will be delated)
digit one of the previously setted 4 digit codes+ 6 + ENTER. The LED on the keypad will start blinking, press again on ENTER ( within 1,5sec.) and hold pressed until the LED blinks, then release Enter .The keypad will
make a BEEP to confirm the procedure has been compleeted.
WARNING: the Keypad will go back to the standard code =1111 but with this standard code it will not be possible to command anymore the opener. It will be necessary to re-set a new personalized code following
instructions of point 1 above.
B) To erase your KEYPAD from the control board of your opener:
To deactivate any unwanted remote, erase its memory from the electronic board of your opener as following (all remote control codes memorized will be delated):
- The door must be closed and idle.
- Press button P1 for about 20 sec. until the red LED blinks
- Release P1.
- All remote control codes have been delated.- Reprogram each remote you wish to use following procedure on point A)
