background image

The lamp used is manufactured from quartz glass and should be handled with care. Always
adhere to the instructions supplied in the lamp's packaging. Never touch the glass directly but
use the tissue provided in the lamp's packaging. The Gy 9.5 lampbase (MSD250)is not
symmetrical; the G12 lampbase (CDM-T 150) is simmetrical.

. In case of difficulty, re-read the

instructions and repeat the procedure.

Attention: we recommend that the lamp be realigned in the optical train of the unit (Photo 4).

Alignment is carried out using the 3 adjusters.
During this operation you must bring the hot-spot to the centre of the beam and flatten it as
much as possible.

The projector can operate at 230V voltage, at 50-60Hz . D.T.S. presets a voltage of 230V at
a frequency of 50Hz (barring specific requests).

may be either floor or ceiling mounted.

For floor mounting installations, the

is supplied with four rubber mounting feet (B)

on the base. For ceiling mounted installations, we suggest the use of appropriate clamps or
fixings to attach the fixture to the mounting surface.
Two holes situated at the base of the unit allow for the mounting of the unit with C clamps on
trussing.

DO NOT USE UNDUE FORCE ON THE GLASS

A.R.C.

A.R.C.

3.1 -Alignment lamp:

4 -VOLTAGE AND FREQUENCY

5 -INSTALLATION

Photo 4

6

INSTALLAZIONE A TERRA

INSTALLAZIONE A SOFFITTO

www.bluelight.at

Summary of Contents for A.R.C.
















Reviews: