background image

10

electric connector of the device is disconnected or reconnected.

In case of any failure of the device, please do NOT open the case and repair without permission from a
professional personnel, to avoid accident or additional damages to the device.

Please do NOT place any corrosive chemicals near or on the device.

2

Matters needing attention

Our company provides a three-year free warranty service (including free replacement parts) over quality
issues as from the date of purchase, provided that the device is installed and used in accordance with
requirements specified in the User Manual.

For warranty, the user must show the Warranty Card and the receipt kept by the user and purchase
invoice of the device as supporting documents.

The following conditions are beyond the scope of warranty:
1

Product damage due to improper installation, use or handling;

2

Product damage due to abnormal conditions (such as excessive power source voltage or ambient

humidity);
3

Product damage due to acts of God;

4

Product SN is changed, altered or removed;

5

Product has been repaired or modified by any person without duly authorization from our company;

Please keep the User Manual and Warranty Card in good custody.

For issues and precautions not mentioned in this User Manual, if required, please contact the distributor
or visit our website at

http://www.DSPPA.com

.

In case of any failure in the warranty period, please contact service personnel (or distributor) of our
company for service. The company shall not be made liable for damages due to unauthorized
dis-assembly or maintenance or service by unauthorized personnel.

Summary of Contents for MAG2126
















Reviews: